I have a Nova 24 machine and use lightburn. I have looking over other discussions and this and have tried everything that people have indicated. Any other thoughts on this issue?

Liam

2023-02-28

988

1

0

High-performance commercial laser color printer, due to its high definition and special color, has high requirements for paper, and is used for drum driver. It is necessary to further reduce the speed fluctuation and prolong the service life. Therefore, the transmission device is driven by precision planetary reducer, which has high service life an...

jessie

2023-02-28

968

0

0

Hello I'm designing a CNC diode laser machine that can cut 16-Gauge stainless steel to earn my bachelor's at the university.Since Im new to this enviroment I would like to know how to calculate the power needed to cut that deep, I've searching this forum for answers but all I can find is people estimating 150-500W and not the actual formulas or par...

Henry

2023-02-27

1.3K

4

0

Laser week, we developed a new postprocessor for plasma bevel cutting machine, the control START Sharpon is used on it.Thanks for the new tool management feature involved in CutLeader V6, we could add severial tools with different bevel angle and the enty/exit radius.Based on the tool assignment rules, the bevel tool can be assigned to contour auto...

Jamie

2023-02-27

923

2

0

Hi everyone, I have purchased a used Chinese laser recently and it has had one of its limit switches removed. Probably removed because it was broken. So I purchased a new proximity switch and replaced it. Now when I home the machine it slides to the right and when it activates the switch it just stops and gives me the error, hard limit prot. It doe...

Smith

2023-02-27

1.2K

1

0

My 40-50W co2 laser cuts 1/4" plywood and acrylic well at 50% but above 50%, the cuts get shallower as I increase the power. The current stays approximately proportional to the power setting, but the beam seems to get weeker. Is this normal or a sign of a partucular failure?The tube has less than 100 cutting hours, mostly at about 45%. I almost nev...

Miller

2023-02-27

1.2K

1

0

Hi all,I have a D.I.Y. build 130W with a Cloudray MYJG-150W.Everything has been running great for a few weeks and now the laser will only fire at 100%.Anyone able to help with this one?

Vasili

2023-02-27

1K

2

0

Aufero 2, Windows 10, Lightburn 1.3.01. Cutting 3mm plywood using 200mm/min at 100% power 2 passes, was not quite getting through the plywood completely. I decided to add a sub-layer at a higher speed (500mm/min at 80%) to “clean up” the cut. The sublayer did NOT align with the primary layer.

Nugent

2023-02-27

1.3K

3

0

I know how to do a square at the size i want, but for the life of me, i can figure out how to draw a circle to the size i desire. Can someone help?

Christian

2023-02-27

958

1

0

I have MP-30 LiteMarker 30W Split Laser Engraver… I have EZCAD 2 and have installed the driver just fine. I have adjusted the focus. I have used the EZCAD 2 that was shipped with the laser.

Tory

2023-02-24

1.2K

1

0

I have a 50W Raycus marking machine. The 50W Raycus source got a red laser diode inside source and in my machine the red line focus is about 10mm above fiber focus, it give me a thick line.

Darren

2023-02-24

1.3K

1

0

I have a 50W Raycus fiber marking and i noticed that when the red laser is showing the engraving area it goes out of focus in relation to or focus of the fiber laser. For example: if I use a 110x110mm f-theta, the red laser focus is around 12mm above the fiber laser focus, which makes the red line thicker. I don’t know how to solve because un...

Cyril

2023-02-24

1.1K

1

0

Guys, please help.Just recently joined and have Sculpfun S30 pro 10w.Was trying to engrave slate. Found it very hard at the beginning. Settings all over the place as there are so many different opinions.Saw big improvements lately with trial and error. More error!My latest settings were 1500/35 on fill.I would still like to get it a bit sharper on ...

Patrick

2023-02-24

964

1

0

can’t access laser control commands in device settings for Marlin. there is a line there but can’t open

jessie

2023-02-24

1.1K

1

0

I have a 100w reci laser with a JYJG 80w PSU(came with the machine when I bought it). I think PSU is fried now and I have to replace it. I know it was undersized but I rarely used the laser anywhere near full power which I presume is why it lasted 4 years.On the machine I mostly engrave wood and cut sandpaper so my 100w reci is oversized. I...

Gilbert

2023-02-24

1.2K

1

0