I updated to V1.4 and the numbers in the height/width/% boxes only show the numbers to the right of the decimal point. can’t figure out how to fix this. please see attached screenshot. thanks

John Trant

2023-06-06

422

1

0

How do i revert back to flat or plane cutting on my boss laser LS1420 machine? Just finished using the rotary set up and it been difficult getting back to flat engraving mode despite all my efforts.I use lightburn and have no issues with the software

Robert Evans

2023-06-06

264

1

0

I tried clicking “fill” but didn’t see anything happen and I’m not sure that’s the solution. TIA

Henry

2023-06-06

470

1

0

LioniX International, a provider of integrated photonics and custom MEMS device solutions, has teamed up with an alliance partner in the REAP program to develop an ultra-narrow line-width tunable laser ona chip that addresses the narrow range of near-infrared light. It is described as having a line width of 22 kHz, a tuning range of 45 nm, an outpu...

Marshall

2023-06-05

317

1

0

High power Industrial Blue Light Lasers has announced that it has signed a joint technology agreement with GE Additive Manufacturing, a subsidiary of GE Aviation, to explore the speed, accuracy and commercial benefits of blu-ray laser-based metal 3D printing."As we continue to advance our proprietary blue laser technology, we further increase the...

Kevin

2023-06-05

253

1

0

Ireland's University of Galway is working with the Tyndall National Institute at University College Cork to create two-dimensional semiconductors for low-cost sensors.The €200,000 project "two-dimensional semiconductor Pulsed Laser Annealing for Nanoelectronics" aims to dramatically improve the scalability, functionality, performance a...

Aaron

2023-06-05

296

1

0

The need to reduce the size of semiconductors, coupled with the problem that heat generated at device hot spots cannot be dispersed efficiently, has a negative impact on the reliability and durability of modern devices. Existing thermal management techniques are not up to the task. The discovery of a new way to dissipate heat by using surface waves...

Abel

2023-06-05

362

1

0

I’m working on a guitar fretboard. Usually the fret dots go in the middle of the fret board, which is easy to figure out in lightburn. But for this particular board I want the fret dots to be dead center on the left half between the edge of the fretboard and the center line. And also dead center between the two frets. Any ideas?

Williams

2023-06-05

420

1

0

What is causing this?Grbl 1.1f [‘$’ for help][MSG:‘$H’|‘$X’ to unlock]$X[MSG:Caution: Unlocked]okWaiting for connection…ok[VER:1.1f.20180715:][OPT:VMZ,35,254]Target buffer size foundokHomingok<Idle|WPos:0.000,0.000,0.000|FS:0,0|WCO:0.000,0.000,0.000>okStarting streamALARM:2G-code motion target exceed...

Smith

2023-06-05

356

1

0

hi there , i did stupid thing and tried to upgrade my Ortur 2 S2 laser firmware and now it wont turn on.when i press power and reset button it comes up on my computer to put firmware in but when i turn that off it wont power up.ive started Lightburn and did this to see if Lightburn would see the laser but it says it isnt conectedcan i please get so...

Miller

2023-06-05

404

1

0

Hullo peoples lovely to meet you all!I’m a retired architect and set designer and I’m turning my design and fabrication skills to making 1:24 scale miniatures.I’m used to laying out pieces for cutting on a table saw where I try to make it so individual pieces share a cutting line to reduce waste.Is that not possible with laser cut...

Darren

2023-06-05

469

1

0

I have tried resetting the default layout, changing my tool bar size and font sizes but am unable to get Art Library to go into the tabs where Cuts, Move and Console are located. Have tried adjusting the display resolution (1366 x 768), but to no avail. My HP laptop is about 3-4 years old.What I want to accomplish is to have Laser and Library on th...

Cyril

2023-06-05

294

1

0

Is there a way to change the preferences so Lightburn will look for svg files instead of Lightburn files. Most of my files are svgs and I’m slowly converting them over but every time I go to open a file, it automatically is looking for lightburn files. I have to drop down the choices and tell it to look for all supported files. I’d like...

Gilbert

2023-06-05

342

1

0

Hi, I have been trying to engrave the Text on wood using milling cutter, however when I import the file from Illustrator to Vcut works it changes the image and cuts only boarder lines as a cut out.How can i engrave the entire world instead of making it a cut out. Can any one guide ?Regards

Hussain Raza

2023-06-05

454

1

0

Humanetics Biomed, the prominent industrial technology group, has made significant progress in expanding its outsourced manufacturing capabilities into new markets. With a 50-year history of providing high quality strain sensors, material processing, laser microprocessing, fiber optic processing and fiber optics, Humanetics Biomed has firmly establ...

Nugent

2023-06-02

290

1

0