Laser cladding generally uses materials such as iron-based alloys, nickel based alloys, titanium alloys, Al Si alloys, stainless steel, etc.The materials for laser cladding are mainly metallic materials, including iron-based alloys, nickel based alloys, titanium alloys, Al Si alloys, stainless steel, and so on. These materials have good melting p...
02-1917700When repairing the grounding fault of the armature winding of a DC motor, we can use various techniques. Firstly, it is necessary to ensure the use of convenient and practical maintenance tools, such as armature maintenance lights. Connect the lamp to the circuit and clarify the fault situation through the operation method. If the light is on after...
02-1818900Everything works great except lightburn is not tracking, in the program, my laser’s movement. The laser is burning, it works fine. But as you can see on the attached image, the upper green and red squares? Those never move.Any advice is appreciated, I searched but didn’t find anything that helped, maybe just a link in the right direction? Appreciat...
02-1517540Possible causes of malfunction:Excessive clearance of bearings due to wear and tear;Uneven air gap affects the balance of the motor;Unbalanced rotor leads to vibration;The bending deformation of the shaft affects the operation of the motor;Iron core deformation or looseness, affecting the stability of the motor;The center of the coupling (or pulley...
02-1721900Principle of adjusting laser powerThe power of the laser marking machine directly determines the depth and speed of marking. Different materials have different requirements for laser power, and adjusting the laser power to be just right can ensure the best marking effect.Choose the appropriate power size1. Metal materials:For metal materials, hig...
02-1518400Reasons for poor laser weldingPoor laser welding can be caused by various reasons, such as improper welding parameter settings, poor quality of welding materials, improper preparation of welding surfaces, and malfunction of welding equipment.1. Improper setting of welding parametersWhen the parameters such as laser power, focal length, and focal ...
02-1416500Cuts/Layers.When I slect “fill” it does not fill the text or object in the work area? What am I missing?
02-1218620Switched from rollers to chuck and now the image/texts are reversed. Did I miss a setting somewhere. Are they different from using the rollers to the chuck? Xtool D1 Pro 20W with RA2 Rotary. Any advice appreciated.
02-1021740Reasons for black welding in laser weldingThe blackening of laser welding is generally caused by the following reasons:1. Gas pollution: During laser welding, impurities in the gas may cause incomplete melting, resulting in blackening of the weld surface.2. Insufficient energy: If the energy of the laser is insufficient, the temperature of the wel...
02-1315401What would suddenly cause the camera to be about 2 inches off in the Y axis? I was using the camera for a few cuts to salvage some scrap and it was working perfectly as usual then from one set up to the next, it framed two inches higher in the Y axis than showed in the picture, There were no bumps or shocks to the lid or cabinet, the alignment was ...
02-1117920I am just learning and new, still on the trial package. In the lightburn program and I am wondering why the mirror button doesn’t show up to use anywhere, not on the tool bar and not down the Arrange section. Maybe I have to turn it on but have no idea and have search the net over and over but nothing about the missing button. I know about how to c...
02-0825250Hi everyone i just started to experiment with puzzles on my laser and have seen almost all vids on the topic on Youtube Lots of good information.BUT our “friend” called Kerf is an acurring issue. My experience now is that its two solutions to deal with the kerf. If you are going to engrave your design directly on the puzzle, you can just separate e...
02-0729160This design with ruida software RDWorks V8And I cut it from ruida rdc6445g and results was amazing do you try it link is here 👇👇https://m.chanelink.com/share/design/1294
01-2329278I have 150W Chinese Laser machine, it is is fitted with Ruida RDC6445S(EC), it is double head laser machine. Head 1 is connected with CN-5 and Head 2 is connected with CN-6.I have issue since I received the machine, Head 1 is firing laser normally, but Head 2 does not fire, I have double checked all the setting in Ruida controller and RDWorks.Whe...
01-16631121Aluminum magnesium manganese plate price is affected by the following factors.The price of aluminum magnesium manganese plate varies depending on various factors such as material specifications,production processes,market demand,international market conditions and exchange rate fluctuations.The following is an overview of aluminum magnesium mangane...
21852
- No Data
English
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski