The controller used in my machine is the Ruida RDV6555G. When performing vision-based positioning machining and activating the Mark point matching function, a pop-up window displays C++ garbled charac...

• RDV6555G
• control system
• RuiDa

Hello！ I use RDWorksV8 for machining, and I open the mark module to set the markings. However, as soon as the module was clicked to start, the software interface immediately closed and automatically e...

• RDWorksV8
• control system
• laser cutting
• RuiDa

Hello everyone! My device control system is RDD6584G. After I power on the device, the controller automatically enters the running state and starts executing default tasks. I originally planned to con...

• RDD6584G
• control system
• RuiDa

My CO2 vision cutting equipment is paired with the RDV6445G control system. During vision positioning, I've encountered instances where mark points are either misidentified or not recognized at all. A...

• camera
• CO₂ visual cutting
• RDV6445G
• control system
• RuiDa

When my Ruida RDD6616U control device is operating, everything functions normally during low-speed movement. However, when the X/Y axes transition to high-speed operation, noticeable stuttering occurs...

• coordinate axis
• RDD6616U
• control system
• RuiDa

I tried to import a new drawing for the RDC6555G control system, but the system suddenly crashed during the import process. Every time a drawing file is selected and loaded, the controller interface f...

• RDC6555G
• control system
• laser cutting
• RuiDa

I am planning to use the RDD6616U controller for cutting, and I have set the tool lifting coordinates to ensure that the tool can be lifted to the designated position in non cutting state. However, du...

• RDD6616U
• control system
• RuiDa

Hello everyone! I have a fiber laser cutting machine that is equipped with a Ruida control system, model RDC6563FG. During use, the machine suddenly triggered a Z-axis servo alarm. When an alarm occur...

• motion system
• coordinate axis
• RDC6563FG
• control system
• RuiDa

My device is equipped with the RDC6555G control system. I am preparing to cut the workpiece, but I found that there are significant differences in the cutting effect of the device in different directi...

• coordinate axis
• RDC6555G
• control system
• laser cutting
• RuiDa

i pressed the emergency button now has file transfer from a computer to the laser clip is showing and everytime i restart my laser it always shows this and i dont know how to get rid of it.. please he...

• RDC6445G
• LightBurn
• control system

Hello! I encountered a problem while using the RDC6555G control system for laser cutting: the cutting paths in the same graphic are confused. After preparing the cutting file, I followed the usual ste...

• motion system
• RDC6555G
• control system
• laser cutting
• RuiDa

My fiber laser equipment uses the RDV6563FG control system. Today, I was operating normally for processing, but I found that the cutting head had a large following error. During the operation of the e...

• RDV6563FG-NET
• laser head
• fiber laser
• control system
• RuiDa

RDC6445GZ-DFM-RD control system, when I opened the template file, the interface did not display the corresponding graphic content, and the template list was empty. Is this due to file corruption or so...

• CO₂ visual cutting
• RDC6445GZ-DFM-RD
• control system
• RuiDa

My CO2 laser cutting machine is equipped with an RDC6685U control system. I am now planning to encrypt the motherboard. How should I proceed? Thank you!

• RDC6685U
• control system
• CO₂ laser
• RuiDa

My CO2 laser cutting equipment uses the Ruida control system, model RDC6332NM. Today, I started processing normally, but found that it cannot be reset to the origin. Can anyone help check? Thanks!

• coordinate axis
• RDC6332NM
• control system
• CO₂ laser
• RuiDa