When I was debugging the device, the RDC6685U controller frequently prompted the "distance limit" alarm. Whenever the machining axis moves to a specific position, the system automatically limits and i...

• camera
• RDC6685U
• control system
• RuiDa

Hello everyone, I have encountered a new problem again, RDV6445G， The cross shaped pattern cut always has deviations, and the distance of deviation varies greatly, making it difficult to fix. I checke...

• motion system
• RDV6445G
• control system
• RuiDa

When I started the RDV6563FG control system, it prompted an X-axis servo fault, causing the machine to malfunction. What items should I check? seek help.

• coordinate axis
• RDV6563FG-NET
• control system
• RuiDa

I encountered an issue with setting invalid positioning points while using the RDC6585G controller for device debugging. When I tried to set the positioning point through the control panel, no matter ...

• RDC6585G
• control system
• laser cutting
• RuiDa

My device is paired with the RDC6332NM control system. Every time the system triggers an alarm, the relay should trigger the alarm light to flash, but in reality, the alarm light never lights up. Chec...

• RDC6332NM
• control system
• RuiDa

When using the RDC6585G controller, the device always displays a collision warning with the pressure limit switch after each power on. Even if the power is turned off and restarted, the laser head con...

• RDC6585G
• control system
• RuiDa

My device is using the RDV6332M control system, and I was about to perform visual positioning, but I found that the camera lighting was never on. Whether switching the light source switch in the softw...

• camera
• CO₂ visual cutting
• RDV6332M
• control system
• RuiDa

I started the processing, but the double beam equipment suddenly malfunctioned during processing, with one fast and one slow, causing an instant deviation and collision with the machine. I immediately...

• RDC6685U
• control system
• laser cutting
• RuiDa

The control system used for my device is RDC6332NM. During the machining task, I tried to activate the device by calling the preset positioning point through the controller panel, but the machine neve...

• RDC6332NM
• control system
• laser cutting
• RuiDa

The dual beam multi head laser equipment I am using is equipped with the Ruida control system RDC6612U. During the debugging process, I found that the main head and the auxiliary head can move and pos...

• RDC6612U
• control system
• RuiDa

I have a CO2 laser cutting machine with a control system of RUIDA's RDC6442G. I have enabled absolute coordinates, but the equipment suddenly moves rapidly in the wrong direction while executing proce...

• RDC6442G
• control system
• CO₂ laser
• RuiDa

I found that the punch cannot rotate while operating the RDD6584G control system. The system is powered on normally and there are no alarms on the display interface, but the punch does not respond aft...

• rotate
• RDD6584G
• control system
• RuiDa

The controller used for my device is RDV6555G, which has been connected to a grating protection device. However, in actual operation, I tried to block the grating multiple times, but the machine conti...

• RDV6555G
• control system
• laser cutting
• RuiDa

RDD6616U vibration knife control system, I think I operated something wrong, the tool cannot be lifted during the cutting process. What should I do if the tool remains pressed down and cannot be lifte...

• RDD6616U
• control system
• RuiDa

My device uses the RDC8445S control system. Today, when I was processing, I set the U-axis to the rotation axis, but the original multi-point positioning function of the device cannot be used properly...

• RDC8445S
• control system
• CO₂ laser
• laser cutting
• RuiDa