- Gelöst
Why is my RDC6612U control panel displaying an out-of-bounds error?
Today, I operated the equipment for machining as usual. The controller model is RDC6612U. I attempted to set the machining area in the software, but the control panel suddenly displayed an out-of-boun...
- RDC6612U
- control system
- laser cutting
- RuiDa
- 2 Benutzer haben geantwortet
248 Solution for collision of RDC6612U-DFM and RDC6685U-DFM dual beam equipment
If encountering the problem of double beam equipment collision using RDC6612U-DFM and RDC6685U-DFM control systems, the following two aspects can be investigated and adjusted: 1. Check whether the ma...
- RDC6612U
- RDC6685U
- laser cutting
- RuiDa
Michael26413- Gelöst
The mutual moving head of the RDC6612U vision controller is not working,how can I solve this issue?
When I use the RDC6612U vision controller for processing, the equipment appears to be functioning normally: the camera can take photos and perform recognition, and the system can accurately complete v...
- coordinate axis
- RDC6612U
- control system
- laser cutting
- RuiDa
- 3 Benutzer haben geantwortet
262 Troubleshooting Method for Slow X-Axis Reset in CO2 Laser Cutting and Engraving Control System
When using CO2 laser cutting and engraving control systems such as the RDC6612U or RDC8445S, if the X-axis reset speed is slow, follow these steps to systematically check for potential causes and make...
- coordinate axis
- RDC6612U
- RDC8445S
- CO₂ laser
- RuiDa
Caspar24902Solution for CO2 cutting and carving controller, computer unable to recognize USB driver
When using the CO2 laser cutting and engraving controller, if the computer cannot recognize the USB driver and displays that it cannot be installed, you can follow the following steps to troubleshoot ...
- USB
- RDC6612U
- RDC8445S
- CO₂ laser
- RuiDa
Michael24402- Gelöst
RDC6612U, HMI prompts file incompatibility
It's really puzzling. My device is using Ruida's RDC6612U controller, and the HMI pop-up file is not compatible. I checked the firmware version and it's not a problem. What should I do next to solve i...
- RDC6612U
- control system
- CO₂ laser
- laser cutting
- RuiDa
- 2 Benutzer haben geantwortet
263 RDC6612U features dual-measurement and multi-head mutual shifting,the main head emits light, while the auxiliary head does not, how to solve it?
When using the RDC6612U control system for dual-head multi-beam inter-transfer machining, if the following phenomenon occurs: the equipment operates normally in its trajectory, but only the main head ...
- RDC6612U
- laser head
- control system
- laser cutting
- RuiDa
Thomas23503- Gelöst
RDC6612U-DFM cannot use the two end separation function normally
The first time I operated the Ruida control system, model RDC6612U-DFM, all other settings and operations were normal. However, when the system was performing the "two end separation" machining functi...
- RDC6612U
- control system
- laser cutting
- RuiDa
- 2 Benutzer haben geantwortet
254 - Gelöst
RDC6612U， The problem of virtual array graphic processing
The controller used for my device is RDC6612U. After downloading the virtual array graphics drawn on the computer to the control panel, there was a significant deviation in locating the actual machini...
- RDC6612U
- control system
- laser cutting
- RuiDa
- 3 Benutzer haben geantwortet
254 - Gelöst
Secondary positioning error of RDC6612U control system
I've encountered a new issue with my equipment. The control system is RDC6612U, and an error occurred during the execution of the secondary positioning program, resulting in a significant deviation be...
- camera
- RDC6612U
- control system
- laser cutting
- RuiDa
- 3 Benutzer haben geantwortet
257 - Gelöst
How to upgrade the firmware version program of RDC6612U motherboard
I use the Ruida control system RDC6612U for my CO2 cutting machine. How can I upgrade the firmware version program on the motherboard?
- RDC6612U
- control system
- CO₂ laser
- laser cutting
- RuiDa
- 1 Benutzer hat geantwortet
268 - Gelöst
I used RDC6612U-DFM to cut the cross out of alignment
My machine is equipped with the RDC6612U-DFM control system. After calibration today, the cross I cut still did not align properly and showed offset. What should I do?
- camera
- RDC6612U
- control system
- laser cutting
- RuiDa
- 3 Benutzer haben geantwortet
300 - Gelöst
The calibration of RDC6612U small vision cutting has a significant deviation on both sides
I encountered a problem last week and haven't had time to find an answer. I used RDC6612U small vision cutting to calibrate the center of the cross accurately, but there was a large deviation on both ...
- RDC6612U
- laser cutting
- RuiDa
- 3 Benutzer haben geantwortet
305 Problem after push "stop" button RDC6612U
Hello, I have dual gantry machine with RDC6612U mainboard. If I push "stop" button during cutting process then gantries moving back to home position and one of gantry hit into second gantry. After thi...
- RDC6612U
- control system
- laser cutting
- RuiDa
2E66B82965211RDC6612U how to input alarm from servo driver to mainboard
Hello, Can someone support me with connect alarm info from servo driver to ruida main board ? It should works as below: If some error exist on driver, then I have info on operation panel, and workin...
- motion system
- RDC6612U
- control system
- RuiDa
2E66B82966430
RDC6612U
30
Themen8
Follower
Warten auf Antworten
- RDworksV8可以加工锤子画吗？
- Where can I download the firmware upgrade file for the RDC6445 series controller?
- After installing the RDWorksV8 plugin in CorelDRAW, how can I do engraving and cutting at the same time?
- Edge tracing for contour cutting
- How do I adjust the time displayed on the C320？
- problema na cnc
- Mantisoft User guide or Manual
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.