- Gelöst
RDC6612U controller, cutting graphics opposite to software display
Hello everyone! My device is equipped with the RDC6612U control system, but I found that the cutting result is in the opposite direction of the graphics displayed in the software. Is this a coordinate...
- RDC6612U
- control system
- RuiDa
- 3 Benutzer haben geantwortet
254 - Gelöst
The RDC6612U controller failed to recognize during the large-format matching test
My device uses the Ruida control system RDC6612U. During the large-format matching test, the target device was not recognized. At the start of the test, the system passed its self-check, but after con...
- RDC6612U
- control system
- RuiDa
- 2 Benutzer haben geantwortet
138 - Gelöst
RDC6612U controller exhibits abnormal Z-axis movement
My CO2 laser cutting equipment uses the RDC6612U control system, but I found that the Z-axis movement is abnormal. When I long press Z - or Z+for about 4 seconds, the Z-axis keeps moving down or up. W...
- coordinate axis
- RDC6612U
- control system
- CO₂ laser
- RuiDa
- 2 Benutzer haben geantwortet
221 - Gelöst
RDC6612U controller point shooting sub cutting head does not emit light
The dual beam multi head laser equipment I am using is equipped with the Ruida control system RDC6612U. During the debugging process, I found that the main head and the auxiliary head can move and pos...
- RDC6612U
- control system
- RuiDa
- 3 Benutzer haben geantwortet
215 - Gelöst
Why can't the RDC6612U-DFM matching test recognize it?
The control system used for my CO2 visual cutting equipment is RDC6612U-DFM. When I conducted a matching test, I found that the material could not be recognized. Is it a problem with the sensor? Or is...
- camera
- CO₂ visual cutting
- RDC6612U
- control system
- RuiDa
- 2 Benutzer haben geantwortet
239 - Gelöst
RDC6612U controller, large visual drawing grid acquisition format prompt y format super border
Hi， I would like to ask a question about the RDC6612U controller. When performing laser cutting operations on the large vision system, I encountered a problem while drawing the grid to obtain the form...
- RDC6612U
- control system
- RuiDa
- 2 Benutzer haben geantwortet
214 - Gelöst
Why does the RDC6612U controller display communication failure after a delay of 30 seconds when reading files?
My RDC6612U control system has encountered a new issue. As usual, when I select the processing file, the screen first displays "Reading" normally, and the progress bar slowly advances. However, after ...
- RDC6612U
- control system
- CO₂ laser
- laser cutting
- RuiDa
- 3 Benutzer haben geantwortet
240 - Gelöst
How to solve the distance limitation problem of RDC6612U-DFM recognition mark points?
My CO2 visual control system is RDC6612U-DFM, and I found that the equipment recognizes Mark points within the processing range but frequently prompts distance limitations. Even though the location is...
- CO₂ visual cutting
- RDC6612U
- control system
- RuiDa
- 2 Benutzer haben geantwortet
215 - Gelöst
RDC6612U，Propose the inner contour when lifting the edge, what should I do?
My device uses the CO2 visual cutting control system RDC6612U. During the edge cutting operation, the system extracted the inner contour instead of the outer contour as originally set. The edge cuttin...
- CO₂ visual cutting
- RDC6612U
- control system
- RuiDa
- 3 Benutzer haben geantwortet
219 - Ungelöst
The RDC6612U controller displays the message “Motherboard is encrypted”
While machining with the RDC6612U controller, I encountered a message stating: “The mainboard is encrypted.” How do I decrypt it? Do I need to contact the manufacturer?
- RDC6612U
- control system
- CO₂ laser
- laser cutting
- RuiDa
- 1 Benutzer hat geantwortet
216 - Gelöst
How to deal with the problem of the RDC6612U control system beam 1 getting stuck during processing?
My CO2 visual cutting control system is RDC6612U. During the processing of crossbeam 1, the equipment suddenly froze and could not continue normal operation. I tried to restart the control system, but...
- coordinate axis
- CO₂ visual cutting
- RDC6612U
- control system
- RuiDa
- 2 Benutzer haben geantwortet
230 - Gelöst
Why can't RDC6612U-DFM be positioned and processed using crossbeam 1?
I have been using the RDC6612U-DFM controller for about 2 weeks now, and some of the operations are not very familiar. Today, I found that I cannot use crossbeam 1 for positioning processing. I am not...
- RDC6612U
- control system
- laser cutting
- RuiDa
- 2 Benutzer haben geantwortet
233 RDC6612U controller virtual array graphics downloaded to panel positioning processing position error
When using the RDC6612U controller, encountering the problem of incorrect positioning of the virtual array graphics after downloading to the panel may be caused by various factors. To solve this probl...
- RDC6612U
- control system
- RuiDa
Caspar20200Solution for RDC6612U Controller Intershift Head Unable to Perform Operations
To address the issue of the RDC6612U controller's inter head being unable to perform operations, the following steps can be taken to systematically troubleshoot: 1. Check the Enable Status and Signal...
- coordinate axis
- RDC6612U
- laser cutting
- RuiDa
Adrian19711RDC6612U-DFM/RDC6685U-DFM secondary positioning error handling method
When using the RDC6612U-DFM/RDC6685U-DFM control system, a secondary positioning error may result in inaccurate positioning or splicing failure. Here are two effective methods to address this issue: ...
- camera
- RDC6685U-DFM
- RDC6612U
- laser cutting
- RuiDa
Matthew19900
RDC6612U
30
Themen8
Follower
Warten auf Antworten
- RDworksV8可以加工锤子画吗？
- Where can I download the firmware upgrade file for the RDC6445 series controller?
- After installing the RDWorksV8 plugin in CorelDRAW, how can I do engraving and cutting at the same time?
- Edge tracing for contour cutting
- How do I adjust the time displayed on the C320？
- problema na cnc
- Mantisoft User guide or Manual
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.