How to encrypt the motherboard?

Abel

2022-12-10

285

5

1

RDC6442, the software version before V8.0.06, draws a diagram and downloads it to the motherboard, but "file incompatibility" will appear when the panel is processed. It is OK to download it again, I don't know why?

Andrej

2022-11-14

258

8

4

So I have a RDC6432G on my Omtech laser. I’m having problems getting my rotary to work.I have seen posts about when enabling rotary the commands are sent out the U axis. This does not seem to be the case with this controller, but if anyone knows how to change it to use U axis, that would actually help some.I have the Manfield ...

CXje56nO

2024-01-28

67

1

1

Hallo everyone!I hope you can help me, I’m slowly running out of ideas.I’ve upgraded my old 130w CO2 laser from a Puhan Ph3 controller to a new Ruida RDC6445Scontroller (complete set).Laser power supply, motor drivers, etc., remained the same.The conversion itself was not difficult.Now, everything seems to work fine.Home posit...

Pr0phezz

2024-01-27

75

1

0

Recebo esse erro "Attempted to access an unnamed file past its end' quando tento abrir um arquivo importado de outro computador com a mesma versão do sotfware. Versão RDCutist V3.0 3.02.20

Rene

2024-01-13

65

1

0

Hi, I'd like to add an extra 230Vac FAN to our lasercutter. The fan may only be active when the lazer itself is also active (cutting or scanning) When the proces is finished, the fan has to stop as well. In other words, the fan will only worg when there is a production of smoke. Any idea how I can control this?

DcoscfnG

2023-12-28

42

4

0

I have seen others add 2 solenoids to CN1 so they have low pressure and high pressure air assist. They use pin 6, +24 for the + connection on the solenoids and then pin 5, wind for the - side of one solenoid followed by pin 4, status for the - connection on the other solenoid. Why is pin 1, - not used and are these connections correct?...

1SaaRNJb

2023-12-29

62

2

0

I have an Ruida RDC6563FG laser controller controlling a Max laser.If I manually open the Max laser shutter off the Ruida control panel the shutter opens and the laser fires correctly.But when I create a program using RDCUTIST, the program runs through its sequence, but the laser shutter does not open.Any help would be appre...

Cityslicker

2023-07-19

267

7

0

Do you need to actiuvate RDcutist software to use it ?

Cityslicker

2023-11-15

76

3

0

There is support for ruida?I am using rdcutist 3.02.20 beta.I have the following problems:- Frame speed is very slow, can't change it.- If I connect parts and load them into RG6563FG. Cutting occurs with a visit (not always)- Focus, axis A can only be controlled in external coordinates. - IMPORTANT: In layer, membrane mode - does not turn on t...

Pavel_TT

2023-08-30

333

23

4

Hi,My machine has a rdc6563f controller an i use rdcutist 3I have worked out most issues but i cannot find how to continiue a cut after a collision.If i have a part stand up and the laser head touchs it , the machine stops and an alarm is then on the screen(collision).It asks to press esc to clear.I clear the alarm and when I then press st...

ROD

2023-11-02

76

2

0

Hi everyone!Please help with RDC6563FG controllerHeught senson has no effect in HMI panel, if i chorted nozzle to earth, i dont see the alarm in controllerI bought a new one aplifier, and this sensor dont worked tooAnd axis Z has not moving any way, i checked up to PIN8(DA) in Z axis motor interface, and i have only 0v in this pin. Any ideas how a ...

hqEbIakv

2023-10-19

88

1

0

Hello everyone, I want to use the RDC6445G controller for the first time and I have some doubts:1- is it not necessary to reset the axes?2- Are the inputs on the CN3-CN4 connectors related to the hardware limit switches?3- where can I find all the documentation?4- Are the outputs on the CN1 connector programmable?Thanks in advance

Cruise Wang

2023-04-18

194

2

0

Hello!I can't adjust the gas pressure regulator.in the setting, the slok costs 1MPa. ITV2030 shows 0.75MPa.Can you tell me how to do the same?

Pavel_TT

2023-07-10

295

5

0

HiI have read the manual of RDC6563F and RDC6563FG-LITE (in Chinese). I understand the difference between these models. I don't know how to connect the BM111 cutting head with AutoFocus. Can you help me? Which axis of the RDC6563 controller controls the AutoFocus function of this head and how to change it in the RDCutist 3.02.20 software. Can the ...

Robertulus

2023-09-18

77

3

1