Can Lasergrbl be used for carving and cutting in the same project?My machine is a 10W laser
10-2811740While cutting on the Atomstack X24 Pro, the laser head encountered an obstacle on the work surface. Since then, the y-axis movement has not been performed correctly. The movement and noise are like rattling.Can anyone tell me what I should check to find the cause and, if possible, eliminate it?
3 days ago71101. What is Annealing?Annealing is a heat treatment process that involves heating steel to a predetermined high temperature, holding it for a specified duration, and then cooling it slowly. This method heats the steel to a temperature where phase transformation or partial phase transformation occurs, followed by slow cooling after holding.In the m...
10 hours ago3500Laser tube cutting machines hold a pivotal position in metal processing, enabling the fabrication of complex shapes, precise connections, and accurate cuts. They have revolutionized industries ranging from furniture manufacturing to aerospace. Scientific parameter optimization can significantly enhance cutting quality, increase production speed, an...
3 days ago8300During the use of laser cutting machines, it is inevitable to encounter various problems, which can lead to unsatisfactory processing results. Here are 10 common problems that cause laser cutting failures.1. Contaminated Protective LensesTouching protective lenses with bare hands or neglecting to clean off dust can significantly reduce their tran...
10-30101001. Can diode laser cutting cut transparent acrylic?After fine adjustment of relevant parameters, the diode laser (≥ 30 W) can cut transparent acrylic with a thickness of about 6 millimeters.Laser PowerUse 65–70 % of the diode’s peak output to balance cut quality and speed.Cutting SpeedAim for 5–8 mm/s: slower speeds risk excessive melting; faster...
10-299100The weather is getting colder day by day, and machines and equipment, like humans, need to be kept warm. The following article introduces the key points related to antifreeze for laser cutting machines.1.Do not turn off the chillerAfter the laser cutting machine is not working, do not turn off the water cooler when ensuring that the power supply w...
10-2810800Laser cutting of thick steel plates has become a part of daily manufacturing, but laser cutting of thick plates still faces some challenges: energy must penetrate deeply, molten material must be cleanly discharged, and the cutting edge must remain stable over long distances. The following are the main challenges faced by the workshop and mature sol...
10-2215421Myth 1: High equipment costsReality: Although the initial investment in a laser tube cutting machine may seem substantial, the long-term operational costs can be competitive compared to other cutting methods. Laser tube cutting machines offer high efficiency, minimal material waste, and reduced setup times, resulting in lower overall production cos...
10-2713900In general, the most direct way to improve processing efficiency is to increase the laser power. When the 60000 watt laser cutting machine was launched, it sparked discussions.Industry experts believe that 60000 watts have the ability to fully replace plasma and flame cutting. Further increasing power does not contribute significantly to cutting e...
10-2515300Fiber lasers have the advantages of high precision, efficiency, and versatility, and are widely used in industries such as manufacturing, construction, and packaging. So, what materials can fiber lasers cut?Metal Materials1.Stainless SteelFiber laser cutting excels in processing stainless steel, achieving remarkable cutting depths of up to 0.75 i...
10-24153001. Diagonal cutting of metal pipesDiagonal cutting on metal pipes usually refers to oblique cutting at the edge of the pipe, rather than vertical (90 degree) cutting. Diagonal cutting is usually done at a 45 degree angle, but can also be adjusted to other angles depending on the application. This cutting method can achieve precise connections, espe...
10-23166001. Introduction to the Flying Cutting Function of Laser Cutting MachineWhen laser cutting circular or parts with circular inner holes, the cutting method of moving the laser head from one part to another without lifting the head is called flight cutting, which can significantly improve cutting efficiency.2. Different Types of Laser Fly Cutting Fun...
10-2116101In the metal manufacturing industry, laser cutting has become the default choice. Mastering the process control of laser cutting stainless steel and carbon steel can improve production efficiency and part quality.Choose the right laser family for the jobTwo laser technologies dominate industry use: fiber lasers and CO₂ lasers. For most modern shop...
10-2017300I want to use a metal plate to make a laser bed. What is the size of the hole?
10-1517420
- No Data
English
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski