I have a CO2 laser cutting machine with a control system of RUIDA's RDC6442G. I have enabled absolute coordinates, but the equipment suddenly moves rapidly in the wrong direction while executing proce...

• RDC6442G
• control system
• CO₂ laser
• RuiDa

When using RDVisionWorks for large-scale visual processing, I prepared to connect the device for matching, but the software still couldn't recognize the visual system. After clicking the matching butt...

• RDVisionWorks
• RuiDa

I found that the punch cannot rotate while operating the RDD6584G control system. The system is powered on normally and there are no alarms on the display interface, but the punch does not respond aft...

• rotate
• RDD6584G
• control system
• RuiDa

The controller used for my device is RDV6555G, which has been connected to a grating protection device. However, in actual operation, I tried to block the grating multiple times, but the machine conti...

• RDV6555G
• control system
• laser cutting
• RuiDa

RDD6616U vibration knife control system, I think I operated something wrong, the tool cannot be lifted during the cutting process. What should I do if the tool remains pressed down and cannot be lifte...

• RDD6616U
• control system
• RuiDa

My device uses the RDC8445S control system. Today, when I was processing, I set the U-axis to the rotation axis, but the original multi-point positioning function of the device cannot be used properly...

• RDC8445S
• control system
• CO₂ laser
• laser cutting
• RuiDa

When I tried to open my AI file with RDworkV8, it failed. I tried double clicking to open and dragging to import, but could not succeed. What is the reason? Is it a version issue?

• RDWorksV8
• RuiDa

Hi everyone, we have a specific use case we’d like to try with our laser, but we aren't getting good results. Controller: RDV844XS(EC), Camera: SV300-New CCD, Software: RDWorks V8 Machine setup: Wo...

• RDWorksV8
• control system
• laser cutting
• RuiDa

I installed an RD6432G with RD Works, I performed all the suggested tests and parameter changes to activate the water sensor, the WP signal does not appear as activated on the panel, I am connecting t...

• RuiDa

I encountered a problem when using RDWorksV8 for laser cutting processing: the XY axis cannot be properly limited. Every time the device is started, the XY axis does not automatically reach the limit ...

• coordinate axis
• RDWorksV8
• RuiDa

As soon as my RDC6332NM control system is powered on, the cutting head always moves upwards without stopping. It switches to manual mode, which can control the motor movement, and then switches to aut...

• motion system
• RDC6332NM
• control system
• RuiDa

The control system used for my device is RDC6555G, and I encountered a problem during the reset operation. After a brief flashing message was displayed on the panel, there was no response immediately,...

• RDC6555G
• control system
• laser cutting
• RuiDa

When I use RDWorksV8 for processing, the laser cutting function performs normally, and the finished product size is consistent with the design drawing. However, when switching to the brush function fo...

• RDWorksV8
• laser cutting
• RuiDa

My device is equipped with the Ruida control system RDC6332NM. After normal connection, when I press the automatic focus button, the cutting head keeps moving upwards and cannot stop. Is there a malfu...

• motion system
• RDC6332NM
• control system
• RuiDa

The control system used for my device is RDV6563FG-NET, which was functioning normally before, but today I found that it cannot establish a communication connection through USB. After the device is co...

• USB
• RDV6563FG-NET
• control system
• RuiDa