- 未解决
The air assist switch enabled by RDC 6445S in LightBurn is not responding
My Ruida RDC6445S controller (firmware version RDC6445S-V26.01.19) does not respond to the Air Assist switch command enabled in LightBurn. However, the solenoid valve operates normally when connected ...
- assist gas system
- power supply
- RDC6445S
- LightBurn
- RuiDa
- 1 位用户已回答
50 - 已解决
RDC6555G controller laser cannot be controlled
I am using the RDC6555G controller to prepare for processing, but I have found that the laser cannot respond to commands properly. Whether adjusting the power or modifying the path parameters, the las...
- power supply
- RDC6555G
- control system
- laser cutting
- RuiDa
- 3 位用户已回答
295 - 已解决
Why doesn't the RDC6332NM controller emit light?
My CO2 laser cutting equipment is equipped with the Ruida control system, model RDC6332NM. In the spot shooting mode, when I press the start button, it cannot emit light. I checked the laser power sup...
- power supply
- RDC6332NM
- cooling system
- CO₂ laser
- RuiDa
- 3 位用户已回答
222 - 已解决
RDC8445S controller motherboard cannot be used
I found an abnormality in the motherboard during routine equipment inspection of the RDC8445S control system. The panel originally used to control laser engraving and cutting cannot start, and the scr...
- power supply
- RDC8445S
- laser engraving
- laser cutting
- RuiDa
- 2 位用户已回答
212 - 已解决
Why does the RDC8445S controller automatically reset to the origin?
My CO2 laser cutting machine uses the RDC8445S control system. Today, I found an abnormality while operating it. Every time the processing program starts, the originally set processing point will auto...
- power supply
- RDC8445S
- control system
- CO₂ laser
- RuiDa
- 2 位用户已回答
216 - 已解决
Why isn't the power indicator light on my RDC8445S controller working?
I encountered a problem today, the power indicator light of my RDC8445S controller suddenly stopped working. Normally, this indicator light should be on to display the power status of the controller, ...
- power supply
- RDC8445S
- control system
- RuiDa
- 2 位用户已回答
236 - 未解决
RDWorksV8, how can I resolve the issue of the laser not emitting light?
I started RDWorksV8 normally, and everything is set up and ready to go, but the laser is not emitting any light at all. I checked the equipment, and the laser shows no signs of operation, even though ...
- power supply
- laser source
- RDWorksV8
- cooling system
- RuiDa
- 1 位用户已回答
251 - 已解决
Why does the RDV6563FG-NET controller generate a machine protection alarm when processing the motherboard?
I have a fiber laser cutting machine with a ruida controller RDV6563FG-NET. Today, I was operating normally for processing, but suddenly a machine protection alarm occurred, causing the processing to ...
- power supply
- RDV6563FG-NET
- fiber laser
- control system
- RuiDa
- 3 位用户已回答
245 Solution for CO2 visual cutting controller that cannot be displayed by Medview camera
When using the CO2 visual cutting controller, if you encounter an issue where the Medview camera cannot display, you can troubleshoot the following: 1. Check whether the connection cables are normal ...
- camera
- power supply
- CO₂ visual cutting
- control system
- RuiDa
Howard20111Troubleshooting method for laser emission during RDC6685U empty range
When using the RDC6685U controller, the issue of laser emission during idle range may be caused by multiple factors. Here is a detailed troubleshooting method that can help you quickly locate and solv...
- power supply
- RDC6685U
- laser head
- control system
- RuiDa
Jerome20100- 未解决
How to solve the problem of insufficient laser engraving depth in RDC6585G controller?
I operate a CO2 laser engraving machine for engraving, with the control system being RDC6585G. The light intensity and speed settings meet conventional requirements, and the engraved patterns and text...
- power supply
- beam delivery system
- RDC6585G
- laser engraving
- RuiDa
- 1 位用户已回答
217 Inspection items for invalid exit of fiber laser cutting control system
The fiber laser cutting control system cannot be exited and restarts after a period of time, which may be related to panel communication, power supply, or interface issues. The following aspects can b...
- power supply
- RDV6563FG-NET
- RDC6563FG
- control system
- RuiDa
Caspar20200Troubleshooting Method for Flashback of Vibration Knife Control System Panel during Operation
When using the vibration knife control system, the operation panel of models RDD6584G and RDD6616U often experiences a flashing phenomenon during operation, which often affects the continuity of proce...
- power supply
- RDD6584G
- RDD6616U
- control system
- RuiDa
Spark22800Solution for the laser not emitting light when using RDWorksV8
When using RDWorksV8 for processing, if you encounter the problem of the laser not emitting light, you can follow the following methods to troubleshoot and solve it: 1. Check the Water Protection Fir...
- power supply
- laser source
- RDWorksV8
- cooling system
- RuiDa
Gary24301- 已解决
RDC6685U-DFM, the MindVision camera cannot display
My CO2 visual cutting machine uses a Ruida controller, model RDC6685U-DFM, with a MindVision industrial camera. When connected, the camera fails to display.
- camera
- power supply
- CO₂ visual cutting
- RDC6685U-DFM
- RuiDa
- 3 位用户已回答
271
power supply
32
话题4
粉丝等待回答
- RDworksV8可以加工锤子画吗？
- Where can I download the firmware upgrade file for the RDC6445 series controller?
- After installing the RDWorksV8 plugin in CorelDRAW, how can I do engraving and cutting at the same time?
- Edge tracing for contour cutting
- How do I adjust the time displayed on the C320？
- problema na cnc
- Mantisoft User guide or Manual
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.