My CO2 visual cutting machine uses the RDV6332M control system. When I adjust the camera exposure and gain parameters, the operation response is significantly slow. Every time I adjust the parameters,...

• camera
• CO₂ visual cutting
• RDV6332M
• control system
• RuiDa

The control system I am using with my device is RDC6685U, and I encountered an issue while operating the HMI interface. When attempting to open or upload a file, the system pops up a prompt saying 'Fi...

• RDC6685U
• control system
• RuiDa

When I was debugging the device, the RDC6685U controller frequently prompted the "distance limit" alarm. Whenever the machining axis moves to a specific position, the system automatically limits and i...

• camera
• RDC6685U
• control system
• RuiDa

Hello everyone, I have encountered a new problem again, RDV6445G， The cross shaped pattern cut always has deviations, and the distance of deviation varies greatly, making it difficult to fix. I checke...

• motion system
• RDV6445G
• control system
• RuiDa

I don't know if anyone else has encountered this problem. When using RDWorksV8, I found that the graphics bridge function is not fully displayed. The complete graphics bridge position and parameter se...

• RDWorksV8
• RuiDa

When I started the RDV6563FG control system, it prompted an X-axis servo fault, causing the machine to malfunction. What items should I check? seek help.

• coordinate axis
• RDV6563FG-NET
• control system
• RuiDa

I encountered an issue with setting invalid positioning points while using the RDC6585G controller for device debugging. When I tried to set the positioning point through the control panel, no matter ...

• RDC6585G
• control system
• laser cutting
• RuiDa

The control system used for my laser cutting machine is RDV6555G. Today, there was a significant cutting offset issue during processing. I changed the material for testing and the problem still exists...

• RDV6555G
• laser cutting
• RuiDa

My device is paired with the RDC6332NM control system. Every time the system triggers an alarm, the relay should trigger the alarm light to flash, but in reality, the alarm light never lights up. Chec...

• RDC6332NM
• control system
• RuiDa

When using the RDC6585G controller, the device always displays a collision warning with the pressure limit switch after each power on. Even if the power is turned off and restarted, the laser head con...

• RDC6585G
• control system
• RuiDa

My device is using the RDV6332M control system, and I was about to perform visual positioning, but I found that the camera lighting was never on. Whether switching the light source switch in the softw...

• camera
• CO₂ visual cutting
• RDV6332M
• control system
• RuiDa

I have a fiber laser equipment equipped with the RDV6563FG control system, but the laser emits a rapid alarm sound. The screen is flashing and indicating an abnormality, and the beam is interrupted. I...

• laser source
• RDV6563FG-NET
• laser cutting
• RuiDa

I started the processing, but the double beam equipment suddenly malfunctioned during processing, with one fast and one slow, causing an instant deviation and collision with the machine. I immediately...

• RDC6685U
• control system
• laser cutting
• RuiDa

The control system used for my device is RDC6332NM. During the machining task, I tried to activate the device by calling the preset positioning point through the controller panel, but the machine neve...

• RDC6332NM
• control system
• laser cutting
• RuiDa

The dual beam multi head laser equipment I am using is equipped with the Ruida control system RDC6612U. During the debugging process, I found that the main head and the auxiliary head can move and pos...

• RDC6612U
• control system
• RuiDa