Français

20W High Power Fiber Optic Frequency Comb with 10 to 19 Power Outside Ring Frequency Stability

425
2023-10-20 14:19:08
Voir la traduction

High power optical frequency combs play a crucial role in nonlinear precision spectroscopy, extreme ultraviolet optical frequency comb generation, nuclear atomic clock research, and other fields. Fiber optic femtosecond lasers are the preferred solution for achieving high power optical frequency combs due to their simple structure, stable performance, and easy amplification. However, due to the unavoidable spontaneous emission (ASE) noise, pump intensity noise, spectral coherence degradation, and phase jitter caused by optical path in fiber laser amplification, the frequency stability of the optical comb is seriously affected. Therefore, obtaining high frequency stability while amplifying high power is a highly challenging task.

In response to the above problems, Group L07 of the Institute of Physics of the Chinese Academy of Sciences/Key Laboratory of Optical Physics of the National Research Center of Condensed Matter Physics in Beijing, based on long-term research on optical frequency comb technology, has proposed in recent years the use of low-noise fiber seed source, linear chirped pulse amplification, rapid phase modulation of intracavity electro-optic crystals and other technical solutions, And by using tapered photonic crystal fibers to generate high coherence supercontinuum spectra and combining various engineering designs such as structural integration, temperature control, and vibration isolation, the noise of optical frequency combs is effectively reduced.

Recently, associate researchers Han Hainian and postdoctoral fellow Shao Xiaodong of the group further achieved an external frequency stability of 10-19/1000s on a 20W high average power fiber optic frequency comb. It is known that this has achieved the frequency stability of the best optical atomic clock currently available, and is also the best result achieved by high-power optical frequency combs to date. Figure 1 shows the schematic diagram of two identical high-power fiber optic comb engineering prototypes and the measurement of frequency stability through the comparison of external dual combs.

In the study, a self built nonlinear polarization rotation mode locked (NPR) fiber laser oscillator was used as a femtosecond seed pulse source. After linear fiber chirped pulse amplification (CPA), a high-power femtosecond laser output with an average power greater than 20 W and a pulse width of 75 fs was obtained. The locked frequency stability of the carrier envelope phase shift (CEO) frequency is 1.5 × 10-17/s. When locking the optical frequency, the femtosecond pulses output from different branches of the oscillator and amplifier and the ultra stable reference laser beat separately. If the beat signal of the amplifier is used for locking, the frequency stability inside the high-power amplification laser ring can be measured to reach 2 × 10-18/s, while in the case of only locking the femtosecond pulse output of the oscillator, if the amplifier is allowed to operate freely, the frequency stability can only reach 10-15/s, which is three orders of magnitude different.

The noise power spectrum analysis shows that the amplifier introduces a large amount of low-frequency noise, which has a significant impact on the long-term stability of the optical frequency comb frequency. At a gate time of 1000 s, this difference can even reach four orders of magnitude, as shown in Figure 2 (a). In addition, the phase noise analysis results that characterize the short-term stability of the frequency also indicate that after a series of noise control measures, the high-frequency noise introduced by the amplifier is very small and does not affect the short-term stability of the system.

In order to evaluate the frequency stability performance of the high average power optical frequency comb in practical applications, this study conducted the first measurement of external frequency comparison between two 20W high-power fiber laser frequency combs. The measurement results indicate that under 1 second integration time, the typical stability value of the out of loop frequency is 4.35 × 10-17/s, 1000 s integration time drops to 6.54 × 10-19, as shown in Figure 2 (b), will open up new doors for many applications that require high-power and high frequency stability optical combs.

The research progress was recently published in Optics Express under the title "High power optical frequency comb with 10-19 frequency feasibility". (Opt. Express 31 (20), 32813-32823 (2023)). The first author of the article is Shao Xiaodong, and the collaborating mentors are Wei Zhiyi and Han Hainian. The work was supported by the Chinese Academy of Sciences pilot projects (XDA150204004, XDB210104004) and the National Natural Science Foundation of China (60808007613780401107802291850209).

Figure 1 (a) Photos of the prototype of the engineering principle of high-power optical fiber comb, (b) Schematic diagram of the measurement of frequency stability outside the high-power optical frequency comb ring


Figure 2 (a) Frequency stability locked by oscillator and amplifier respectively, (b) Frequency stability compared to high-power optical frequency comb ring

Source: Institute of Physics, Chinese Academy of Sciences

Recommandations associées
  • Overview of ultrafast laser micro nano manufacturing technology: material processing, surface/interface control, and device manufacturing

    Researchers from Tsinghua University have summarized the research on ultrafast laser micro nano manufacturing technology, including material processing, surface/interface control, and device manufacturing. The relevant review titled "A Review of Ultrafast Laser Micro/Nano Fabric: Material Processing, Surface/Interface Control, and Device Fabric" was published in Nano Research.Ultra fast laser proc...

    2024-08-06
    Voir la traduction
  • Laser engraving: Researchers have created a revolutionary technology

    Recently, a group of researchers from the University of Cambridge developed an innovative method of using high-energy lasers to improve 3D printing of metals. This discovery has the potential to change the way we design and manufacture complex metal objects.3D printing has completely changed the landscape of the manufacturing industry. However, it faces obstacles, especially in terms of the charac...

    2023-11-24
    Voir la traduction
  • Marilli won the "2024 CES Innovation Award": Laser and optical taillights produce 1mm of light

    Marelli is a company specialized in the field of automotive lighting, which has won the prestigious "2024 CES Innovation Award Winner" for its revolutionary red laser and fiber optic taillight technology. This innovative solution, showcased at the 2024 Consumer Electronics Show, for the first time combines the functionality of red laser with taillights, opening up a new perspective for car design....

    2024-01-16
    Voir la traduction
  • Topological high-order harmonic spectroscopy in Communications Physics

    It is reported that researchers from the University of Salamanca in Spain have demonstrated a high-order harmonic spectroscopy scheme generated by the interaction between a structured driving beam and a crystal solid target. This work promotes the topological analysis of high-order harmonic fields as a spectroscopic tool to reveal nonlinearity in the coupling of light and target symmetry. The rele...

    2024-01-15
    Voir la traduction
  • Real time measurement of femtosecond dynamics of relativistic intense laser driven ultra-hot electron beams

    In the interaction between ultra short and ultra strong lasers and matter, short pulse width and high energy electrons are generated, commonly referred to as "hot electrons". The generation and transport of hot electrons is one of the important fundamental issues in high-energy density physics of lasers. Superhot electrons can excite ultrafast electromagnetic radiation in a wide range of wavelengt...

    2024-06-21
    Voir la traduction