What I want is the image in green (bottom right).The way to get there is what I think can be much easyer.How I tried to do:1 - Imported a DXF image and use “offset shape” tool on them resulting im the red image (Upper left)2 - Create a rectangle with “Create Rectangle” tool, using “create array” tool create an a...

Nugent

2023-05-29

1.2K

1

0

Trying to run material tests, have cutting done. How do I change to engraving for different materials to run my test material files?

Christian

2023-05-29

1.1K

1

0

Short-wave infrared nanofocal low-period laser sources can drive two-color plasma to generate terahertz pulses with higher efficiency, and can also be generated in non-oxide crystals by optical difference frequency. Mid-infrared femtosecond pulse of 5μm. Thulium-doped fiber laser system can produce a thulium-doped fiber pulse with a central wave...

roy

2023-05-29

1K

1

0

Salve a tutti, sono praticamente un neofita del settore ma ho esperienze di grafica per cui volevo provare ad abbinare le due cose per fare piccoli lavori di incisione e intaglio, sia su legno (2/3 mm) sia su plexiglas e qui per quanto ho letto finora la cosa si complica un pochino. Devo ancora acquistare l'incisore laser e davvero non so quale sce...

Jen

2023-05-29

939

1

0

I have a 10W Grbl laser (Creality Falcon) that I have used to engrave some lines in 3mm birch. The layer is set to 1000mm/min and 80% power and the air pressure is set to ~50% (manual assist), because I’m not cutting.When I run the job with Air Assist off, the line is clean and sharp as seen in the picture, as opposed to when Air Assist is o...

Aaron

2023-05-27

1.2K

1

0

Hello everyone, I am having issues with saving large data files… This problem has occurred to me twice so I am seeking resolution here to avoid many hours of lost work editing data.I am creating a huge project which contains 29 layers of various graphic elements. Each layer is about 15" W x 15" H. Total project length is 75" long x 15" H x ...

Abel

2023-05-27

1K

1

0

A while back LB crashed while editing nodes. Since then, i CANNOT drag N drop ANY type of file into the open program. I even uninstalled and re-installed.Not a nubie. Is there a configuration file that can be edited?Win 11 workstation40GB RAM2 2GB SSIDsproblem started with v 1.3 , im now on 1.4 and it still happens.TIA

Williams

2023-05-27

1.1K

1

0

Am I correct in thinking that if you create a design and add manual tabs, if you then duplicate this using the array tool, the tabs are not copied?I’m doing a large layout, and filling it using the array tool… When the array is complete, and I select all, then hit the Tabs button, the only item showing tabs is the original one I used t...

Smith

2023-05-27

901

1

0

I’m totally new. I have an Atomstack A5 PRO. When I turn on the power, the laser lights up and it immediately goes to the lower left corner. This model has no limit switches, so it will set there and grind away. I kill power right away, but am unable to perform anything with the software because it can’t communicate with the machine.I s...

Miller

2023-05-27

1K

1

0

In my case it’s my Atomstack A10Pro. Connects no problem and will start to run a project, but randomly stops mid-project. Lightburn will still report “Busy” and no information about the stop on the console.

Darren

2023-05-27

1.1K

1

0

how can I change the line thickness?for example: when I drew a line and I don’t want it to be so thick and almost Invisible?

Cyril

2023-05-27

969

1

0

How can I add new fonts to those fonts we already have in Lightburn?

jessie

2023-05-26

1.2K

1

0

Have machine hooked up to a usb port still does not find it.

roy

2023-05-26

1K

1

0

I cannot get lightburn to engrave an image. If I use GRBL it will engrave no problem. In lightburn I get a gcode error. Any help would be great. Thanks, Dave

Liam

2023-05-26

1.1K

1

0

If I enable this setting and set it to a high number, the preview shows a reduced processing time, but I’m not seeing anything speed up when the job is actually processing. It completes in the same amount of time as it did before. Does this function not work for gcode lasers? I have an xTools at the moment.Thanks.

Jen

2023-05-26

1.1K

1

0