- Gelöst
RDV6563FG controller manual mode, why doesn't the XY axis move?
Hello! I have a fiber laser cutting machine that uses Ruida's controller, RDV6563FG， I have a question to ask. In manual mode, the XY axis cannot move. Whether through the control panel or manual butt...
- motion system
- coordinate axis
- RDV6563FG-NET
- fiber laser
- RuiDa
- 2 Benutzer haben geantwortet
245 - Gelöst
My RDC8445S control system, Why does the machine only move in one direction?
My device is paired with the RDC8445S control system, and what confuses me is that the machine can only move in one direction, and no matter how I adjust the input signal, the machine never responds t...
- motion system
- RDC8445S
- control system
- CO₂ laser
- RuiDa
- 2 Benutzer haben geantwortet
268 - Gelöst
What is the reason for the continuous downward movement of the RDC6332M cutting head during automatic focusing?
The RDC6332M control system, when I turn on the automatic focus or follow function, the cutting head will continue to move downwards without any tendency to stop or rebound. Even if the height of the ...
- motion system
- laser head
- control system
- RDC6332M
- RuiDa
- 2 Benutzer haben geantwortet
227 RDWorksV8, solution for movement direction opposite to button direction
When using RDWorksV8 for machining, if the direction of motion is found to be opposite to the direction of the buttons, it is usually caused by the following reasons. Adjustments and repairs can be ma...
- motion system
- coordinate axis
- RDWorksV8
- RuiDa
Michael24711- Ungelöst
Why doesn't the Z-axis motor of RDC8445S controller move in manual mode?
Hello everyone! CO2 laser cutting machine with RDC8445S control system, switch to manual mode, and try to control the Z-axis motor through the Z+and Z - buttons on the operation panel. However, no mat...
- motion system
- coordinate axis
- RDC8445S
- CO₂ laser
- RuiDa
- 1 Benutzer hat geantwortet
276 Solution for manual non movement of Z-axis in fiber laser control system
In the fiber laser control system, in manual mode, when pressing the Z-axis, the cutting head does not move. The common reasons and solutions are as follows: 1. Incorrect servo driver wiring: Imprope...
- motion system
- coordinate axis
- fiber laser
- control system
- RuiDa
Howard21000The handling method for repeatedly cutting the same shape using RDWorksV8 when the shape is not in the same position
When using RDWorksV8 to repeatedly cut the same shape, if the shape is not in the same position, the following steps can be taken to troubleshoot and handle it: 1. Motor driver step loss Step loss...
- motion system
- RDWorksV8
- RuiDa
Jerome19000Correction method for servo motor moving only in one direction
When using RDWorksV8 for laser processing, if the servo motor only moves in one direction, it may be caused by the following reasons: 1. Incorrect direction polarity setting An incorrect direction po...
- motion system
- RDWorksV8
- RuiDa
Caspar20800The reason for the lack of action in the V-axis of the vibration knife control system
When the vibration knife control system (RDD6584G, RDD6616U, RDD6584V-NET) shows no action on the V axis, it can usually be investigated and analyzed from the following aspects: 1. Motor wiring conne...
- motion system
- coordinate axis
- RDD6584G
- control system
- RuiDa
Michael23104Solution to Scanning Shape Tilt in CO2 Laser Cutting and Carving Control System
In the process of CO2 laser cutting and engraving, if there is a phenomenon of scanning pattern tilting, it is usually caused by setting problems between the control system or hardware. The following ...
- motion system
- control system
- CO₂ laser
- laser cutting
- RuiDa
Thomas22304Solution for cutting circular and non-circular shapes with vibration knife control system
When using the RDD6584G or RDD6616U control system with a vibrating knife, if there is a problem of cutting circles that are not round, the following two aspects can be identified and addressed: 1. I...
- motion system
- RDD6584G
- RDD6616U
- control system
- RuiDa
Michael22902Solution for RDC/V6555G Controller Button Movement with XY Axis Unchanged
For the issue of no response on the XY axis when the RDC6555G and RDV6555G controller buttons move, the following steps can be followed to troubleshoot each one: 1. Check whether the wiring is correc...
- motion system
- coordinate axis
- RDV6555G
- RDC6555G
- RuiDa
Jerome23112- Gelöst
The graphics I cut out using RDWorksV8 are not the right size
I have been using RDWorksV8 for a short time. When I perform cutting operations, the size of the cut graphics changes, either enlarged or reduced. The drawings display normally in the software. Can an...
- motion system
- RDWorksV8
- laser cutting
- RuiDa
- 2 Benutzer haben geantwortet
267 Using RDWorksV8, the machine doesn't move on startup, and the reset motion is reversed
When using RDWorksV8, if it encounters startup failure, reverse reset motion, and inability to limit, it is generally caused by the following reasons: 1. Whether the factory parameters for reset are ...
- motion system
- coordinate axis
- RDWorksV8
- RuiDa
Adrian21800- Gelöst
RDC6332M， The cutting head keeps moving upwards during automatic focusing
The control system I use for my device is RDC6332M. After connecting normally, I press the automatic focus button and the cutting head keeps moving upwards. Are there any parameter settings that are i...
- motion system
- control system
- RDC6332M
- laser cutting
- RuiDa
- 3 Benutzer haben geantwortet
283
motion system
82
Themen5
FollowerWarten auf Antworten
- RDworksV8可以加工锤子画吗？
- Where can I download the firmware upgrade file for the RDC6445 series controller?
- After installing the RDWorksV8 plugin in CorelDRAW, how can I do engraving and cutting at the same time?
- Edge tracing for contour cutting
- How do I adjust the time displayed on the C320？
- problema na cnc
- Mantisoft User guide or Manual
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.