- Ungelöst
RDC6445S controller fault assistance
Motherboard: RDC6445S, Version: V26.01.16 Fault Description: Y-axis drift — When running a frame cycle, the Y-axis returns to the home position with a consistent offset in the same direction each ti...
- motion system
- coordinate axis
- RDC6445S
- control system
- RuiDa
- 1 Benutzer hat geantwortet
44 - Ungelöst
Why does the RDV6445G controller have a deviation in cutting the cross?
Hello everyone, I have encountered a new problem again, RDV6445G， The cross shaped pattern cut always has deviations, and the distance of deviation varies greatly, making it difficult to fix. I checke...
- motion system
- RDV6445G
- control system
- RuiDa
- 2 Benutzer haben geantwortet
214 - Gelöst
RDC6332NM controller cutting head movement abnormality
As soon as my RDC6332NM control system is powered on, the cutting head always moves upwards without stopping. It switches to manual mode, which can control the motor movement, and then switches to aut...
- motion system
- RDC6332NM
- control system
- RuiDa
- 3 Benutzer haben geantwortet
226 - Gelöst
Why does the cutting head of RDC6332NM controller keep moving upwards?
My device is equipped with the Ruida control system RDC6332NM. After normal connection, when I press the automatic focus button, the cutting head keeps moving upwards and cannot stop. Is there a malfu...
- motion system
- RDC6332NM
- control system
- RuiDa
- 2 Benutzer haben geantwortet
216 What innovative features do you most want in motion control software?
How to Vote: Select the features you most want to see in the software (multiple choices allowed) and feel free to share additional ideas in the comments!
- motion system
- MantiSoft
Leon2.1K32- Gelöst
How to solve the problem of Z-axis servo alarm in RDC6563FG controller?
Hello everyone! I have a fiber laser cutting machine that is equipped with a Ruida control system, model RDC6563FG. During use, the machine suddenly triggered a Z-axis servo alarm. When an alarm occur...
- motion system
- coordinate axis
- RDC6563FG
- control system
- RuiDa
- 2 Benutzer haben geantwortet
216 - Gelöst
RDC6555G controller cutting path is chaotic
Hello! I encountered a problem while using the RDC6555G control system for laser cutting: the cutting paths in the same graphic are confused. After preparing the cutting file, I followed the usual ste...
- motion system
- RDC6555G
- control system
- laser cutting
- RuiDa
- 2 Benutzer haben geantwortet
222 - Gelöst
Why does the RDC6585G control system keep moving after pressing a key once?
My device control system model is RDC6585G, and I encountered a problem. I pressed the directional keys once on the control panel, and the machine continued to move in the same direction, as if the ke...
- motion system
- RDC6585G
- control system
- laser cutting
- RuiDa
- 2 Benutzer haben geantwortet
210 - Gelöst
Why does the planned position and actual position of the RDV6555G controller not match the coordinates?
My cutting equipment has a troublesome problem, and the controller model used in conjunction with it is RDV6555G. The position planned by the system does not match the actual operating position of the...
- motion system
- RDV6555G
- control system
- laser cutting
- RuiDa
- 2 Benutzer haben geantwortet
226 Using RDWorksV8 to cut out graphics with incorrect size
When using RDWorksV8 to cut shapes, the issue of incorrect shape size may be caused by the following factors: 1. Is the motor step setting correct? The motor step setting is a key parameter that c...
- motion system
- RDWorksV8
- RuiDa
Thomas21600- Gelöst
Could you please help with an encoder error on the RDC6563FG control system?
I have a fiber laser device that is paired with the RDC6563FG control system. As I was about to start cutting, the screen displayed a prompt saying "Encoder Error" and the machine emitted a short alar...
- motion system
- coordinate axis
- RDC6563FG
- control system
- RuiDa
- 3 Benutzer haben geantwortet
232 - Gelöst
What is the reason for the failure of A-axis reset of RDC6563FG controller?
Hello everyone! I am looking for help again. The A-axis reset of my RDC6563FG control system failed, and both the X and Y axes were able to move to the limit position and complete the reset normally. ...
- motion system
- coordinate axis
- RDC6563FG
- control system
- RuiDa
- 2 Benutzer haben geantwortet
219 - Gelöst
How to solve the problem of large state following jitter in RDC6332NM control system?
Hello everyone! I have a question to ask for help. I have been using the RDC6332NM controller for several months now. Today, I checked the laser output status and pressed the test button "." on the pa...
- motion system
- RDC6332NM
- control system
- RuiDa
- 2 Benutzer haben geantwortet
222 - Gelöst
RDV6555G control system, why can't the first point be pieced together?
When using the RDV6555G control system for graphic stitching processing, I found that the first point could not be accurately aligned. At first, only a few files had slight misalignment, thinking it w...
- motion system
- RDV6555G
- control system
- RuiDa
- 2 Benutzer haben geantwortet
229 - Gelöst
RDC6332M， Why doesn't the Z-axis motor move when pressing the Z button on the operation panel in manual mode?
My device is equipped with the RDC6332M control system. Today, I debugged the device and the system switched to manual mode. I pressed the "Z+" button on the panel, thinking that the workbench would s...
- motion system
- coordinate axis
- control system
- RDC6332M
- RuiDa
- 2 Benutzer haben geantwortet
232
motion system
82
Themen5
FollowerWarten auf Antworten
- RDworksV8可以加工锤子画吗？
- Where can I download the firmware upgrade file for the RDC6445 series controller?
- After installing the RDWorksV8 plugin in CorelDRAW, how can I do engraving and cutting at the same time?
- Edge tracing for contour cutting
- How do I adjust the time displayed on the C320？
- problema na cnc
- Mantisoft User guide or Manual
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.