- 已解决
RDV6563FG controller experiences air pressure alarm
My fiber laser cutting machine uses the RDV6563FG control system. Today, while operating, I noticed that the air pressure alarm was constantly flashing on the device screen, the cylinder was acting ab...
- RDV6563FG-NET
- fiber laser
- control system
- RuiDa
- 2 位用户已回答
228 - 已解决
RDV6563FG control system X-axis servo alarm
When I started the RDV6563FG control system, it prompted an X-axis servo fault, causing the machine to malfunction. What items should I check? seek help.
- coordinate axis
- RDV6563FG-NET
- control system
- RuiDa
- 3 位用户已回答
228 - 已解决
Using the RDV6563FG control system, the laser triggered an alarm
I have a fiber laser equipment equipped with the RDV6563FG control system, but the laser emits a rapid alarm sound. The screen is flashing and indicating an abnormality, and the beam is interrupted. I...
- laser source
- RDV6563FG-NET
- laser cutting
- RuiDa
- 2 位用户已回答
302 - 已解决
RDV6563FG-NET control system communication failure via USB connection
The control system used for my device is RDV6563FG-NET, which was functioning normally before, but today I found that it cannot establish a communication connection through USB. After the device is co...
- USB
- RDV6563FG-NET
- control system
- RuiDa
- 2 位用户已回答
237 - 已解决
RDV6563FG control system has exceeded the border limit
I am using Ruida's control system, model RDV6563FG. After I set the processing area, when the system executes the program, the cutting path exceeds the predetermined border. Is this a software setting...
- coordinate axis
- RDV6563FG-NET
- RuiDa
- 2 位用户已回答
220 - 未解决
ich arbeite mit der Steuerung RDC6563FG und Faser Laser 1,5 kw
ich arbeite mit der Steuerung RDC6563FG und Faser Laser 1,5 kw würde gerne Rotation Achse einsetzen für Rohr zu schneiden, welche Achse nehme ich dafür ? Und wie muss ich die Ansprechen , will nur d...
- RDV6563FG-NET
- 1 位用户已回答
248 - 已解决
RDV6563FG controller has a large cutting head following error
My fiber laser equipment uses the RDV6563FG control system. Today, I was operating normally for processing, but I found that the cutting head had a large following error. During the operation of the e...
- RDV6563FG-NET
- laser head
- fiber laser
- control system
- RuiDa
- 2 位用户已回答
213 - 已解决
Why does the capacitance value of RDV6563FG control card decrease?
My laser equipment is paired with an RDV6563FG control card. During today's maintenance inspection, it was found that the equipment was running unstable, occasionally experiencing slow restarts, commu...
- RDV6563FG-NET
- laser head
- control system
- RuiDa
- 2 位用户已回答
225 - 已解决
RDV6563FG controller manual mode, why doesn't the XY axis move?
Hello! I have a fiber laser cutting machine that uses Ruida's controller, RDV6563FG， I have a question to ask. In manual mode, the XY axis cannot move. Whether through the control panel or manual butt...
- motion system
- coordinate axis
- RDV6563FG-NET
- fiber laser
- RuiDa
- 2 位用户已回答
245 - 已解决
Why does the RDV6563FG-NET controller generate a machine protection alarm when processing the motherboard?
I have a fiber laser cutting machine with a ruida controller RDV6563FG-NET. Today, I was operating normally for processing, but suddenly a machine protection alarm occurred, causing the processing to ...
- power supply
- RDV6563FG-NET
- fiber laser
- control system
- RuiDa
- 3 位用户已回答
245 Fiber laser control system,the reason for the significant deviation between the following height and the actual height
In fiber laser control systems(RDC6563FG, RDV6563FG-NET), if there is a significant deviation between the following height and the actual height, it may be caused by the following factors: 1. Long ti...
- assist gas system
- RDV6563FG-NET
- RDC6563FG
- laser head
- RuiDa
Thomas21800The processing method for the shaking of the cutting head of the fiber laser controller at any time
During the processing of fiber laser cutting equipment(RDC6563FG, RDV6563FG-NET), if there is significant shaking of the cutting head when it follows the height, it will not only affect the cutting st...
- assist gas system
- RDV6563FG-NET
- RDC6563FG
- fiber laser
- RuiDa
Howard19800The fiber laser control system triggered the limit switch without cause
When using fiber laser equipment, if the fiber laser controller(RDC6563FG, RDV6563FG-NET) has the limit switch enable function activated, the system interface typically displays a “limit switch trigge...
- RDV6563FG-NET
- RDC6563FG
- fiber laser
- control system
- RuiDa
Adrian20700Solution to capacitance calibration failure of fiber laser cutting control system
The reason for the failure of capacitor calibration in the fiber laser cutting control system (RDC6563FG, RDV6563FG-NET) may involve multiple issues. Here are several common causes of malfunctions and...
- RDV6563FG-NET
- RDC6563FG
- laser head
- fiber laser
- RuiDa
Matthew22311Adjustment measures for Z-axis reset error in fiber optic cutting control system
During the operation of fiber laser cutting equipment, RDC6563FG, RDV6563FG-NET, if there is an abnormality in Z-axis reset, the system interface usually prompts "System Reset Error". This issue will...
- coordinate axis
- RDV6563FG-NET
- RDC6563FG
- fiber laser
- RuiDa
Michael23312
RDV6563FG-NET
31
话题7
粉丝
等待回答
- RDworksV8可以加工锤子画吗？
- Where can I download the firmware upgrade file for the RDC6445 series controller?
- After installing the RDWorksV8 plugin in CorelDRAW, how can I do engraving and cutting at the same time?
- Edge tracing for contour cutting
- How do I adjust the time displayed on the C320？
- problema na cnc
- Mantisoft User guide or Manual
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.