Hi there, I have a fiber laser 60w JPT, I recently sttarted using it and dont have much experience, I tried engraving a mug, and found that the image was stretched accross half the diameter of the mug, It would seem that the speed of the rotary may be a problem but not sure how to set or correct this to suit.
2023-08-1629820Gearmotors use gears to reduce speed, which makes more torque available. The kind of gears used in gearmotors have an impact on the available torque, but also on things like noise levels and accuracy. In fact, one of the more common sources of inaccuracy in gearmotors is due to gear backlash. So reducing the amount of backlash will lead to a more a...
2023-08-1627911Delta Line has expanded its offering of motors with integrated electronics to include stepper motors. These smart stepper motors eliminate the need for a separate drive and controller, providing a complete stepper motor solution in a single, easy-to-integrate device.Delta Line’s ISI57 and ISI60 stepper motors with integrated electroni...
2023-08-1627310HelloI no longer have the color palette on my software at the bottom of the page I can not find it anywhere in the tabs impossible to use my laser cutting thank you for your help.
2023-08-1628410HII have an Atomstack A10 Pro with 10w laser.I’ve seen videos on youtube that cuts 10mm plywood at a speed of 200 and a power of 80% with 3 passes but I can’t even cut 6mm.Could it be some Lightburn setting?
2023-08-1537210I am having trouble with multiple things with Lightburn recently. I am getting “waiting for connection” and error:5 Homing cycle is not enabled in your Grbl settings. How can I fix this?
2023-08-1532510With the SINAMICS S210 next generation servo-drive system, comprising a digitally native drive with wide range of corresponding motors and gearboxes, Siemens brings a new level of high-dynamic, motion control in mid-range operation to stand-alone and multi-axis machines, recently introduced to the North American manufacturing industry.This ...
2023-08-1539410Kollmorgen has launched its AKMA servo motor built specifically for durability, cleanability, and versatility. The motor employs a hardened anodized aluminum surface to offer machine designers a cost-effective hygienic option to stainless steel in medium to heavy washdown applications.The lightweight design of the AKMA motor makes it easy t...
2023-08-1544010hi all I have a neje master 2 plus laser and using lightburn but totally new too this .so ive installed neje driver correctly then lightburn has auto found laser and input limits correctly ye .now I write text on screen and say centre this but when I go to engrave the laser just goes to the end fully then starts engraving how do I get this in corre...
2023-08-1433010Hi guys ,This is my first print.But I think that there is something wrong.The software was downloaded from lightburn and still on trial version.I´m mising something ?Thank you
2023-08-1439510I have a Ortur LM3 and just noticed that after the latest Lightburn and Ortur updates I’m now getting out of round or misaligned burns. I’ve retentioned both the x and y belts and the error has remained consistent after multiple attempts. Based on the fact that after multiple attempts at adjusting the tension and having the problem rema...
2023-08-1427910Brand new to CNC Laser fun! I have a Longer Ray 5 10W where I established the test line speed vs power in the Lightburn Material test. I’ve noticed my project recently not being fully cutout from the 3mm basswood stock. the material test on the right is from today. none of them can be “punched out” unlike those on the left. I have...
2023-08-1435610The compressor is an important component of a laser chiller, which increases its temperature by compressing the refrigerant. Subsequently, the refrigerant releases heat through the condenser, causing its temperature to decrease and enter the evaporator. In the evaporator, the refrigerant absorbs heat and lowers its temperature before entering the c...
2023-08-1424610I am a new Lightburn user. It is a powerful tool, and there are often many ways to do to the same thing, but there is a steep learning curve. As a Windows user, it would be nice to have scroll bars available to move around the workspace. This would make it more user friendly for the novice and make it possible to keep the same tool as one moves aro...
2023-08-1028211Hi guys,Currently running into some issues when engraving glass, hopefully somebody has a good tip for the situation I’m in, let me give you a little backstory first:I run a shop in personalized items, I want to add glasses to my inventory, meaning I will have 8-10 different glasses that I will engrave with a design that is supplied ...
2023-08-1044431
- Veri Yok
Türkçe
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski