- Решено
RDD6584G control system punch does not rotate
I found that the punch cannot rotate while operating the RDD6584G control system. The system is powered on normally and there are no alarms on the display interface, but the punch does not respond aft...
- rotate
- RDD6584G
- control system
- RuiDa
- 2 пользователей ответили
239 - Решено
Why does the dual blade of RDD6584G control system vibrate?
My machine is equipped with an RDD6584G controller. Today, I encountered a problem where there was significant vibration during dual blade cutting, resulting in a decrease in overall stability and mac...
- RDD6584G
- control system
- RuiDa
- 2 пользователей ответили
231 - Решено
How to solve the problem of automatic startup of RDD6584G controller?
Hello everyone! My device control system is RDD6584G. After I power on the device, the controller automatically enters the running state and starts executing default tasks. I originally planned to con...
- RDD6584G
- control system
- RuiDa
- 2 пользователей ответили
199 - Решено
Why didn't the RDD6584G vibrating knife Mark visual positioning machine perform any action?
I was using the RDD6584G vibration knife control system for Mark visual positioning machining when I started the equipment and loaded the machining file, preparing for visual positioning cutting. When...
- camera
- RDD6584G
- RuiDa
- 2 пользователей ответили
266 - Решено
RDD6584G control system cyclic processing without feeding
I operated the vibration knife control system RDD6584G for cyclic processing. In cyclic mode, although the equipment was able to repeat the processing path, the feeding mechanism remained inactive and...
- RDD6584G
- control system
- RuiDa
- 2 пользователей ответили
226 - Решено
RDD6584G touch screen malfunction, how to restore it?
Hello everyone, I need help. I suddenly realized that the touch screen was malfunctioning while using the RDD6584G controller. No matter how I touch the screen, there is no response and the interface ...
- RDD6584G
- control system
- RuiDa
- 2 пользователей ответили
226 Operation steps for collecting signals on the table of the vibration knife control system
The operation steps for signal collection on the vibration knife control system (RDD6584G, RDD6616U, ) are as follows: 1. Preparation: Ensure the vibration knife control system is properly connec...
- RDD6584G
- RDD6616U
- control system
- RuiDa
Ignativs23303- Не решено
RDD6584G controller, how to calculate pulses?
My vibrating knife cutting system is RDD6584G. I have a simple question, how do I calculate the pulse?
- rotate
- RDD6584G
- RuiDa
- 1 пользователь ответил
203 Method of setting the vibration knife control system to not lift the knife at the turning point
Method for setting the vibration knife control system to not lift the knife at the turning point (operation steps instructions) 1. Enter the optimization parameter settings and set the tool lift angl...
- RDD6584G
- RDD6616U
- RuiDa
Jerome20700- Решено
How to solve the abnormal direction of the groove knife under the RDD6584G vibrating knife system?
My device is using the RDD6584G vibrating knife system. Today, I encountered an issue where the direction of the groove knife's cutting is abnormal, and the cutting angle is not consistent with the se...
- RDD6584G
- RuiDa
- 2 пользователей ответили
238 Solution to the insensitivity of the touch screen in the vibration knife control system
When the touch screen of the vibration knife control system is not sensitive, the following methods can be used to handle it: 1. Calibrate the touchscreen through the menu If the touch position is...
- RDD6584V-NET
- RDD6584G
- RDD6616U
- control system
- RuiDa
Ignativs23204- Не решено
How to activate vibration and adsorption during RDD6584G machining?
Hello everyone, I have a question. When I started the RDD6584G control system for processing, I found that the vibration and adsorption functions were not automatically turned on, which resulted in in...
- RDD6584G
- control system
- RuiDa
- 1 пользователь ответил
230 The reason for the lack of action in the V-axis of the vibration knife control system
When the vibration knife control system (RDD6584G, RDD6616U, RDD6584V-NET) shows no action on the V axis, it can usually be investigated and analyzed from the following aspects: 1. Motor wiring conne...
- motion system
- coordinate axis
- RDD6584G
- control system
- RuiDa
Michael23104Solution for cutting circular and non-circular shapes with vibration knife control system
When using the RDD6584G or RDD6616U control system with a vibrating knife, if there is a problem of cutting circles that are not round, the following two aspects can be identified and addressed: 1. I...
- motion system
- RDD6584G
- RDD6616U
- control system
- RuiDa
Michael22902Solution to Invalid RDD6584G/RDD6616U Collision Avoidance Switch
The RDD6584G/RDD6616U control system has encountered an issue with the collision avoidance switch being invalid. The following steps can be taken to troubleshoot and handle the problem: 1. Confirm wh...
- RDD6584G
- RDD6616U
- control system
- RuiDa
Thomas23001
RDD6584G
29
Темы15
Подписчики
Ожидают ответа
- RDworksV8可以加工锤子画吗？
- Where can I download the firmware upgrade file for the RDC6445 series controller?
- After installing the RDWorksV8 plugin in CorelDRAW, how can I do engraving and cutting at the same time?
- Edge tracing for contour cutting
- How do I adjust the time displayed on the C320？
- problema na cnc
- Mantisoft User guide or Manual
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.