- Не решено
The air assist switch enabled by RDC 6445S in LightBurn is not responding
My Ruida RDC6445S controller (firmware version RDC6445S-V26.01.19) does not respond to the Air Assist switch command enabled in LightBurn. However, the solenoid valve operates normally when connected ...
- assist gas system
- power supply
- RDC6445S
- LightBurn
- RuiDa
- 1 пользователь ответил
51 - Решено
RDWelderDW-V2Pro laser handheld welding system does not blow air
My laser handheld welding system is RDWelderDW-V2Pro. During use, I found that the blowing function was not activated as expected during the welding process. I checked that the equipment settings were...
- assist gas system
- RDWelderDW-V2Pro
- laser welding
- RuiDa
- 3 пользователей ответили
220 Dust and smoke control methods and technical selection in laser welding
In laser welding, a large amount of metal vapor, fine particles, and chemical reaction gases are released. These pollutants are difficult to detect with the naked eye, but they will continue to accumu...
- assist gas system
- laser welding
Caspar24503- Решено
RDC6585PC dual board spray cutting integrated layer without blowing air, what should I do?
My dual board spray cutting integrated equipment has encountered an abnormality. The control system model is RDC6585PC, which starts normally, but the layer blowing function cannot be activated. Curre...
- RDC6585PC
- assist gas system
- control system
- laser cutting
- RuiDa
- 2 пользователей ответили
232 - Решено
How to solve the problem of uneven carving bottom in RDC8445S control system?
I used the RDC8445S control system for carving and found that the bottom of the carving was uneven. After careful inspection, I found that this problem occurred in different areas, especially in large...
- galvo scanner
- assist gas system
- beam delivery system
- RDC8445S
- RuiDa
- 1 пользователь ответил
228 RDWorksV8 does not blow air and does not output a signal during machining
During the machining process, the blowing function of RDWorksV8 is not activated and there is no signal output. Possible reasons and troubleshooting suggestions are as follows: 1. Air blower not enab...
- assist gas system
- RDWorksV8
- RuiDa
Adrian25800Fiber laser control system,the reason for the significant deviation between the following height and the actual height
In fiber laser control systems(RDC6563FG, RDV6563FG-NET), if there is a significant deviation between the following height and the actual height, it may be caused by the following factors: 1. Long ti...
- assist gas system
- RDV6563FG-NET
- RDC6563FG
- laser head
- RuiDa
Thomas21900The processing method for the shaking of the cutting head of the fiber laser controller at any time
During the processing of fiber laser cutting equipment(RDC6563FG, RDV6563FG-NET), if there is significant shaking of the cutting head when it follows the height, it will not only affect the cutting st...
- assist gas system
- RDV6563FG-NET
- RDC6563FG
- fiber laser
- RuiDa
Howard19900- Решено
How do I properly focus a Longer Ray5 10W diode laser with air assist?
I’m pretty new to laser engraving and just picked up my first machine, a Longer Ray5 10W. It came with air assist and an Atom rotary attachment. Right now, my biggest issue is focusing. The silver fo...
- assist gas system
- diode laser
- laser cutting
- 1 пользователь ответил
269 - Решено
RDC6563FG-LITE， There is a significant deviation between the following height and the actual height
I haven't operated this fiber laser cutting machine for a while. I used the RDC6563FG-LITE controller and started it up today. I found that there is a significant deviation between the following heigh...
- assist gas system
- RDC6563FG-LITE
- laser head
- control system
- RuiDa
- 3 пользователей ответили
288 - Решено
My RDWelder-SW handheld welding system does not blow gas
I've encountered a new issue with my RDWelder-SW handheld welding system. I was in the middle of a job, and everything else was functioning normally, but I noticed that the shielding gas was not being...
- assist gas system
- RDWelder-SW
- control system
- laser welding
- RuiDa
- 2 пользователей ответили
292 - Не решено
RDC6445G settings for CN1-Output not working right.
Hello again. Sorry for disturbign you again. I´m searching about 21 hours now in the internet and does not find any answer: My complete CN1 is not working right - I think. GND and +24V does work fine,...
- assist gas system
- RDWorksV8
- RDC6445G
- control system
- RuiDa
- 2 пользователей ответили
382 - Решено
I am using the RDC6563FG control card, but there is shaking when the laser head moves with it
I encountered another problem today. My device is equipped with an RDC6563FG control card, but when the laser head moves, it shakes. I don't know if it's due to poor contact or capacitor calibration. ...
- assist gas system
- motion system
- RDC6563FG
- RuiDa
- 3 пользователей ответили
309 - Решено
I am using RDWorksV8 for machining, do not blow air
I am a beginner and have just started working with RDWorksV8. Today, when I was operating the machining, it did not blow air and there was no signal output. What should I do? Thank you in advance for ...
- assist gas system
- RDWorksV8
- RuiDa
- 1 пользователь ответил
323 No blowing during processing, no signal output
Fault analysis: 1. No fan enabled 2. Relay wiring is incorrect 3. Layer setting issue Solution: The layer parameters are set to not blow air
- assist gas system
Aaron1.6K00
assist gas system
18
Темы4
ПодписчикиОжидают ответа
- RDworksV8可以加工锤子画吗？
- Where can I download the firmware upgrade file for the RDC6445 series controller?
- After installing the RDWorksV8 plugin in CorelDRAW, how can I do engraving and cutting at the same time?
- Edge tracing for contour cutting
- How do I adjust the time displayed on the C320？
- problema na cnc
- Mantisoft User guide or Manual
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.