Solution for CO2 cutting and carving controller, computer unable to recognize USB driver
When using the CO2 laser cutting and engraving controller, if the computer cannot recognize the USB driver and displays that it cannot be installed, you can follow the following steps to troubleshoot ...
- USB
- RDC6612U
- RDC8445S
- CO₂ laser
- RuiDa
Michael24702- Resolved
The RDC6585G control system has weak laser output and cannot control the light
I have a CO2 laser cutting machine that is paired with the RDC6585G control system. When I operate it, the laser output is noticeably weak, and there is no response when trying to adjust the power or ...
- RDC6585G
- control system
- CO₂ laser
- laser cutting
- RuiDa
- 2 users answered
264 - Resolved
RDC6612U, HMI prompts file incompatibility
It's really puzzling. My device is using Ruida's RDC6612U controller, and the HMI pop-up file is not compatible. I checked the firmware version and it's not a problem. What should I do next to solve i...
- RDC6612U
- control system
- CO₂ laser
- laser cutting
- RuiDa
- 2 users answered
266 How to solve the problem that the CO2 cutting and engraving controller keeps pressing the limit switch after being turned on?
In CO₂ cutting and engraving equipment, if the limit switch is continuously pressed after startup, there are generally two reasons: 1. Check whether the limit switch itself is functioning properly Fi...
- RDC6442G
- RDC6445G
- control system
- CO₂ laser
- RuiDa
Caspar30215- Resolved
RDC6585G， Cut the square into parallelograms
I have a CO2 laser cutting machine that uses the RDC6585G control system. When I import files and cut square objects, the final result is a parallelogram, which is really frustrating. I have tried sev...
- coordinate axis
- RDC6585G
- CO₂ laser
- laser cutting
- RuiDa
- 3 users answered
259 - Resolved
RDC6685U control system, collision when absolute coordinates are enabled
I have a low-power CO2 laser cutting machine that uses the RDC6685U control system. After enabling the absolute coordinate function, a collision occurred. The system had an error in calculating the co...
- RDC6685U
- laser head
- control system
- CO₂ laser
- RuiDa
- 3 users answered
294 - Unresolved
Does anyone know the maximum distance that the mainboard program of the RDC6685U controller can jog?
I'm not familiar with the control system of Ruida. I'm using the RDC6685U. I have a simple question for everyone: Is there a limit to the maximum distance for jogging the mainboard program? If so, wha...
- RDC6685U
- control system
- CO₂ laser
- laser cutting
- RuiDa
- 1 user answered
283 Abnormal movement of cutting head in CO2 cutting and engraving control system
The cutting head movement of the CO2 cutting and engraving control system is abnormal. Initially, the cutting head kept moving upwards without stopping. When switched to manual mode, the motor movemen...
- motion system
- laser head
- CO₂ laser
- laser cutting
- RuiDa
Spark25700What should you do if the control system of the CO2 laser cutting and engraving series cannot be reset to its original point?
If your control system is one of the RDC6442G, RDC6445G, RDC6585G, RDC6685U, RDC6332NM, RDC6612U, or RDC8445S models from the CO2 laser cutting and engraving series and you encounter an issue where it...
- coordinate axis
- RDC6442G
- RDC6445G
- CO₂ laser
- RuiDa
Howard28522- Resolved
RDC8445S, x-axis reset speed is very slow
I have a CO2 laser cutting machine that uses the RDC8445S control system. When performing a reset to zero operation on the X-axis, its travel speed is abnormally slow, significantly lower than the sta...
- coordinate axis
- RDC8445S
- control system
- CO₂ laser
- RuiDa
- 3 users answered
270 - Resolved
After my RDC8445S control system started processing, the panel displayed a water protection alarm
seek help! It's frustrating! I turned on the machine today to prepare for cutting the workpiece. I turned on the control system and after starting the processing, the panel displayed a water protectio...
- RDC8445S
- control system
- cooling system
- CO₂ laser
- RuiDa
- 4 users answered
272 CO2 cutting carving controller manual operation, Z-axis motor does not move
When using the CO2 cutting and carving series controller, switch to manual mode and press the Z+and Z - buttons on the operation panel. The Z-axis motor will not move. You can follow the following ste...
- motion system
- coordinate axis
- control system
- CO₂ laser
- RuiDa
Thomas29413- Resolved
My RDC6332NM controller preview file shows' no connected device '
My CO2 cutting machine uses the RDC6332NM controller, and when previewing the file, the HMI pops up "No Connected Device". Is there a problem with the link between the device and the controller?
- RDC6332NM
- control system
- CO₂ laser
- laser cutting
- RuiDa
- 2 users answered
267 CO2 cutting and carving control system, how to install USB driver?
The following are measures on how to install USB drivers when using the CO2 cutting carving control system: 1. Connect the hardware: Connect the controller's mainboard to your computer using a USB c...
- USB
- RDC6442G
- RDC6445G
- CO₂ laser
- RuiDa
Adrian31611- Resolved
Should I upgrade my CO2 laser to a combo system or buy separate CO2 and fiber lasers?
I’ve been running the same Chinese 100W 600×900 CO2 laser for close to 15 years now. A few years ago, I upgraded it with a Ruida controller so I could use LightBurn, and honestly, the machine has been...
- diode laser
- laser engraving
- fiber laser
- CO₂ laser
- laser cutting
- 2 users answered
256
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.