- Unresolved
The RDC6612U controller displays the message “Motherboard is encrypted”
While machining with the RDC6612U controller, I encountered a message stating: “The mainboard is encrypted.” How do I decrypt it? Do I need to contact the manufacturer?
- RDC6612U
- control system
- CO₂ laser
- laser cutting
- RuiDa
- 1 user answered
219 - Unresolved
Why doesn't the laser head return to its positioning point after the RDC6445G control system exits?
The control system used for my CO2 laser equipment is RDC6445G, which can return to the set positioning point after processing is completed. However, when the point exited, the laser head did not retu...
- RDC6445G
- laser head
- control system
- CO₂ laser
- RuiDa
- 1 user answered
248 How does the selection of laser type affect marking ability?
Comparison of Mainstream Laser Marking Technologies The most widely used lasers in the current market mainly include fiber lasers and carbon dioxide lasers, both of which have their own advantages an...
- fiber laser
- laser marking
- CO₂ laser
Howard23802- Resolved
Why does my RDC8445S controller have ghosting during scanning?
When using the RDC8445S controller for scanning, I found that the scanning results always showed ghosting. I checked the controller settings, adjusted the resolution and scanning speed, but the proble...
- galvo scanner
- RDC8445S
- control system
- CO₂ laser
- RuiDa
- 2 users answered
230 - Resolved
Why can't the RDC6685U motherboard communicate with the computer USB?
My CO2 cutting machine is equipped with the RDC6685U control system. Today, I tried to connect it to my computer via USB, but it still couldn't communicate properly. I don't know if it's a problem wit...
- USB
- RDC6685U
- control system
- CO₂ laser
- RuiDa
- 3 users answered
251 CO2 laser cutting carving controller XY axis malfunction
When using the CO2 laser cutting and engraving control system, if you encounter this problem: the X-axis stops after hitting the limit switch during power on reset, while the Y-axis is still running s...
- coordinate axis
- control system
- CO₂ laser
- laser cutting
- RuiDa
Thomas21213- Unresolved
Why doesn't the Z-axis motor of RDC8445S controller move in manual mode?
Hello everyone! CO2 laser cutting machine with RDC8445S control system, switch to manual mode, and try to control the Z-axis motor through the Z+and Z - buttons on the operation panel. However, no mat...
- motion system
- coordinate axis
- RDC8445S
- CO₂ laser
- RuiDa
- 1 user answered
278 The frame function of the CO2 laser cutting control system is normal but cannot be started
When the frame function of the CO2 laser cutting control system is normal but the equipment cannot start processing, it usually indicates that the motion system and files of the equipment have been lo...
- control system
- CO₂ laser
- laser cutting
- RuiDa
Caspar18800Steps for upgrading the firmware version program of the CO2 cutting and carving control system motherboard
The steps to upgrade the firmware version of the CO2 cutting and carving control system motherboard can be carried out according to the following process: 1. Open the corresponding software Launch...
- laser engraving
- CO₂ laser
- laser cutting
- RuiDa
Michael21100- Resolved
What is the maximum machining speed of the RDC6445G controller?
My CO2 laser cutter is equipped with the RDC6445G control system. I'd like to test how fast it can cut thin materials at maximum speed. If anyone knows the answer, please let me know. Thanks!
- RDC6445G
- control system
- CO₂ laser
- RuiDa
- 3 users answered
285 Correction method for CO2 laser cutting controller to cut square into parallelogram
When using a CO2 laser cutting controller for processing, if the cut square deforms into a parallelogram, the following methods can be used to correct it: 1. Check and adjust the perpendicularity of ...
- coordinate axis
- control system
- CO₂ laser
- RuiDa
Ignativs19400CO2 cutting and engraving controller cannot communicate with computer via USB
When using the CO2 cutting and engraving controller to communicate with a computer via USB, failure to connect properly is typically caused by the following reasons. Troubleshoot by following these st...
- USB
- control system
- CO₂ laser
- RuiDa
Thomas21900Experience sharing in selecting RuiDa controllers for your CNC machine tools
When choosing a suitable Ruida laser controller for your laser cutting or engraving machine, the first thing to consider is compatibility with the laser type (such as CO2, fiber, or hybrid laser). In ...
- laser engraving
- control system
- CO₂ laser
- laser cutting
- RuiDa
Howard35935- Resolved
How can I fix a "communication failure" when using RDWorks with a Dowin CO₂ laser?
Hi everyone, I’m running into a communication issue when using RDWorks with my Dowin 6090 CO₂ laser, and the software keeps showing a “Communication failure” error. I had the same problem a few mont...
- USB
- RDWorksV8
- CO₂ laser
- 2 users answered
309 Solution for USB Access Failure in CO2 Cutting and Carving Control System
If your CO2 cutting and carving control system encounters a problem of USB access failure, you can follow the following methods to troubleshoot and handle it: 1. Check whether the USB drive file form...
- USB
- laser engraving
- CO₂ laser
- laser cutting
- RuiDa
Thomas21000
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.