Hello. Nesting does not work. I receive an undecipherable message "Г»ХTuSjУГb№". ) Software "VCutWorksSetup2.00.34-20250314". The computer is not connected to the machine, I need to work remotely, do cutting tasks.
07-2211540Hello, I'm upgrading an oscillating knife cutting machine. The machine had a Galileo controller. The PC used to operate it lost its hard drive. I couldn't configure the software from the backup I had.I purchased a Ruida RDD6616u controller from Wavetopsign on Aliexpress. I asked them for the installation manual and software on several occasions. I ...
06-1429870Hi. I have a RDC6445G unit in my 130w CO2 laser. Normally in Lightburn I can choose a Tube Tpe of Glass, RF1, or RF2.Now I want to add a Diode Laser to my unit so I can do very fine detail work that the 130W cannot.My Ruida has 2 outputs, and depending on the mode it will either put out a 0-5v signal to drive the CO2 power supply.. or a PWM signal ...
07-2010710tengo una laser H1610 la encendi y estaba en chino le cambie el lenguaje a ingles pero ya no estaba calibrada la calibre varias veces pero solo hace cut test cuando le doy star no corta hacia los lados ni hacia abajo y solo me corta en un pedazo y lo demas no corta
07-0920870There is support for ruida?I am using rdcutist 3.02.20 beta.I have the following problems:- Frame speed is very slow, can't change it.- If I connect parts and load them into RG6563FG. Cutting occurs with a visit (not always)- Focus, axis A can only be controlled in external coordinates. - IMPORTANT: In layer, membrane mode - does not turn on t...
2023-08-301K255HelloDoes anyone knows, will LightBurn works with Ruida RDC8445S ?I try trial version, and Ruida always in disconnected state, Serial USB/Ethernet IP both not works.PS: RDWorks detect controller by USB and IP (WiFi) - both success
05-1560540I have a 6442s laser cutter, but I want to install a camera to make precise cuts. Please help with the setup.
06-2523810I have 150W Chinese Laser machine, it is is fitted with Ruida RDC6445S(EC), it is double head laser machine. Head 1 is connected with CN-5 and Head 2 is connected with CN-6.I have issue since I received the machine, Head 1 is firing laser normally, but Head 2 does not fire, I have double checked all the setting in Ruida controller and RDWorks.Whe...
01-161.1K142Hello, we have a Ruida controller RDC6563FG for fiber laser cutter. Everything now works fine, except I can't change axis working speed parameters. In the service menu I'm trying to change the parameter Max. work speed, I've entered e.g. 2000 mm/s for axis movements speed. In the USER menus the max manual movement 500mm/s. Above these limits I can'...
06-1923700When using the brush function to rotate the Z-axis instead of the U-axis for machining, there is always a gap reset action，
05-2051840I am a novice, I tried to use an engraving machine to carve some patterns, but I found that the engraving machine did not carve in the correct direction of the pattern, but in the wrong direction. How can I change the setting? I use RDWorksV8 software
05-2759920Buen día me pueden ayudar una máquina láser de 90cm x 60cm me sale en la máquina que el tamaño de trabajo es de 38cm x 30cm como puedo ponerla para 90x60
05-2656920What version of RDworks is supposed to be used with this. I have v8.01.66 and am unable to connect via static wired ethernet or wifi. I can ping both ip's so I know it's online, just no software control via RDworks or lightburn
05-1759660
- Không có dữ liệu
Tiếng Việt
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski
