hope this email finds you well. I am writing to seek clarification regarding a point of discussion we had previously concerning the compatibility of RDV Print with the RD-8445S controller. You had mentioned that RDV Print is not supported on the RD-8445S.However, I had a conversation with the Technical head of Meheta High tech industries my vendor,...

8F4A188E

09-19

559

3

0

The JPT-PS series picosecond lasers are based on the industry-leading amplification architecture for industrial picosecond lasers. Featuring a compact dual-cavity structure and a simple yet reliable electrical control design, they are engineered to meet the demands of 24/7 industrial-grade production as well as advanced scientific characterization ...

Nugent

09-17

520

0

1

Experimental and Mechanism Study of Efficient CFRPCutting Based on Continuous Wave Laser and Water Jet Guided Laser Combined TechnologyAbstractWith the extensive use of large-thickness carbon fibre reinforced polymer (CFRP) in aerospace, one of the key issues that need to be urgently addressed for thick CFRP is to improve the cutting efficiency. W...

Vasili

09-15

618

1

1

Currently using a LS6090 in a secondary school downloading files from RDworks as SVGs (DXFs just go all black on the laser cutter for some reason). Everything is cutting/engraving backwards/mirrored and we can't figure out why. A temporary solution has been to simply mirror designs within RDworks but something has gone wrong somewhere for this to b...

LOB technician

09-12

1.1K

3

0

AbstractThe surface strengthening of ball valves faces challenges such as high dilution rate and grain coarsening. However, high-speed laser cladding (HSLC) reduces dilution rate by reducing heat input through high scanning rate, and refines grain size through rapid cooling. Therefore, in this work, WC composite coating was prepared on the surface ...

Vasili

09-13

663

1

1

The system freezes when accessing the File menu. I cannot click any buttons, and an error message appears as shown in the screenshot. I also cannot read, delete, or manage any files from the File menu. Is there any way to fix this issue or reset the system?https://drive.google.com/file/d/17Vj2YSxcx1MPpqyt3Xit0zr5pvN1LjKC/view?usp=sharing V

CBE1A5C7

09-12

1.1K

1

1

Hello. Nesting does not work. I receive an undecipherable message "Г»ХTuSjУГb№". ) Software "VCutWorksSetup2.00.34-20250314". The computer is not connected to the machine, I need to work remotely, do cutting tasks.

7366BB9B

07-22

1.2K

5

0

what is the default vendor password?

X-Shadow

09-01

733

2

0

Hello everyone,I am using a Ruida 6445G controller for my laser machine and I would like to know if it is possible to lock the machine (or the keyboard panel) with a password.My goal is: when the machine is powered on, the user must enter a password first before being able to control the machine.I tried setting up the password feature, but every...

CBE1A5C7

08-18

1K

3

1

HelloDoes anyone knows, will LightBurn works with Ruida RDC8445S ?I try trial version, and Ruida always in disconnected state, Serial USB/Ethernet IP both not works.PS: RDWorks detect controller by USB and IP (WiFi) - both success 

96DED7E9

05-15

1.5K

5

0

Hello, I'm upgrading an oscillating knife cutting machine. The machine had a Galileo controller. The PC used to operate it lost its hard drive. I couldn't configure the software from the backup I had.I purchased a Ruida RDD6616u controller from Wavetopsign on Aliexpress. I asked them for the installation manual and software on several occasions. I ...

Geozapata

06-14

1.4K

7

0

Hi. I have a RDC6445G unit in my 130w CO2 laser. Normally in Lightburn I can choose a Tube Tpe of Glass, RF1, or RF2.Now I want to add a Diode Laser to my unit so I can do very fine detail work that the 130W cannot.My Ruida has 2 outputs, and depending on the mode it will either put out a 0-5v signal to drive the CO2 power supply.. or a PWM signal ...

7E026F24

07-20

936

1

0

tengo una laser  H1610  la encendi y estaba en chino le cambie el lenguaje a ingles pero ya no estaba calibrada la calibre varias veces pero solo hace cut test cuando le doy star no corta hacia los lados ni hacia abajo y solo me corta en un pedazo y lo demas no corta 

500EA993

07-09

1.3K

7

0

dove trovo l'ordine dei layers in vcutworks

8CE9F5B6

07-09

1K

1

0

There is support for ruida?I am using rdcutist 3.02.20 beta.I have the following problems:- Frame speed is very slow, can't change it.- If I connect parts and load them into RG6563FG. Cutting occurs with a visit (not always)- Focus, axis A can only be controlled in external coordinates. - IMPORTANT: In layer, membrane mode - does not turn on t...

Pavel_TT

2023-08-30

1.9K

25

5