Türkçe
  • I use a new Monport 80w camera with RDC6442G.However, I hit autofocus in Lightburn or the Z-axis menu and the camera breaks. (This camera does not have a Z-axis limit switch).Can I disable the autofocus feature in the control panel or machine settings?I looked at the Ruida manual but it didn't help much with this problem.

    653
    1
    1
  • The servo motor only moves in one direction,How should I handle it?

    05-20
    587
    1
    0
  • Fault analysis:1. The installation path is not selected correctly2. No VBA plugin downloaded3. The VBA plugin version is incorrect compared to the CAD version Solution:The reinstallation path is correct. After checking, it was found that the CAD version sent was 2023 and the VBA plugin version was 2018, which caused the failure. After re downlo...

    05-19
    455
    0
    0
  • Fault analysis:1. No fan enabled2. Relay wiring is incorrect3. Layer setting issue Solution:The layer parameters are set to not blow air

    05-19
    505
    0
    0
  • Fault analysis:1. Layer output setting error2. The laser power setting is too small3. Wrong selection of the number of interchangeable heads Solution:Despite increasing the power, there is still no light, and the cutting action is normalUpon inspection, it was found that the number of interchangeable heads was set to 2, but in reality, there wa...

    05-19
    466
    0
    0
  • Fault analysis:1. Enable multiple positioning points2. Failed to locate successfully3. Panel button malfunction4. Return setting error Solution:Upon checking the user parameters, it was found that the return method has been changed to return to the mechanical origin. Simply change the return to the positioning point

    368
    0
    0
  • Fault analysis:1. Abnormal reset parameters2. Panel reset button malfunction3. Unstable and undervoltage power supply voltage4. Program firmware malfunction Solution:Firstly, check whether the reset parameters are normal, whether the user parameter reset is turned on, whether the motherboard wiring is under voltage, and confirm that the output ...

    05-19
    434
    0
    0
  • I downloaded RDWorks V8, but every time I need to run it, it asks for the administrator. Is there a way to prevent this from happening?

    555
    1
    0
  •  Good evening I made a CNC plasma with a 6442 G rough controller. The machine works perfectly but when I ask it to run the home button it goes in the opposite direction to where I want it to. Even if i change origin of the drawing sheet, the machine continue to reset the axis (both x and y) in the opposite direction (with inversion command) .  i ...

    473
    1
    0
  •  Dear all,I am experiencing an issue when engraving text using RDWorks. Specifically, when I engrave multiple sentences, the machine does not engrave the text in the correct order. Instead, it seems to engrave partial letters from each sentence at once, followed by the remaining letters individually.I have tried adjusting various settings, inclu...

    410
    1
    0
  • Dear Sir,We have an RDC6445S working in a LaserSaur machine, the cutting file come from RDWorks through USB cable.If we place a speed of 100 mm/s in RDworks, the file receive by RDC6445S shows on the screen a speed of 100 mm/s, but the working speed is only 100/5 = 20 mm/s.At the same time, if we tranfer laser head at a 100 mm/s speed (visible o...

    906
    9
    0
  • RDC6563FG Lasercontroller mit dem Maxphotonics MFSC 1500X Laser. Leider bekomme ich die Grundeinstellung zum Schneiden von 1 mm Edelstahl nicht. Wenn ich manuell mit Laser ohne RDC6563FG schneide, bekomme ich sehr saubere Schnitte, aber meine Einstellungen für RDC6563 Auto sind wahrscheinlich nicht korrekt. Bitte für die richtige Einstellung in Rui...

    2024-05-29
    535
    3
    0
  • how do i set up the U axis in RDworks?

    545
    2
    0
  • Pavel, I have the same problem as you. I connected the RUIDA 6563f controller to the MAX MFSC 1500X laser, but I can't turn on the laser from the panel. Do you have an idea! Kind regards, M.

    516
    6
    0
  • Hello.I have RDC 6563FG, laser MAX 1500, BM-110 head and two X-Y axes.I need to place the metal plate at a distance of more than 30 mm from the nozzle and process it with a defocused laser beam.Is it possible to disable the use of the capacitive sensor and not monitor the gap between the metal plate and the nozzle? Otherwise, the message appears - ...

    646
    5
    0