Procedure 1. Calibration: Use a workpiece with a known circumference (e.g., diameter 31.84mm, circumference 100mm) for calibration. Adjust the driver parameters or software settings so that when this...

• rotate
• RDWorksV8
• laser engraving
• RuiDa

roy

2025-12-26

326

0

0

Step 1: Consult Official Specifications Obtain accurate parameters from the stepper motor drive or rotary axis manufacturer. Key Parameters: Stepper motor step angle (e.g., 1.8°), drive microsteppin...

• rotate
• RDWorksV8
• laser engraving
• RuiDa

Gilbert

2025-12-25

329

1

0

Set a speed in LaserGRBL, but engraving occurs at slower speeds. During processing LaserGRBL always command the speed you requested. However, there are reasons why the engraver may move slower. The f...

• motion system
• LaserGRBL
• laser engraving

Patrick

2025-12-19

337

0

0

LaserGRBL work only with boards that implement Grbl. If you are sure that your board is Grbl compatible and you experience connection problem please verify that you are using the proper COM port and c...

• LaserGRBL
• laser engraving

Gilbert

2025-12-19

346

1

0

So I’ll start an engraving and the first couple inches goes where I planned then it jogs over several inches to the right, engraves a couple more inches, then jogs back over in line with the bottom. N...

• laser engraving

Vasili

2025-12-15

488

2

2

I have brought a few of the TEMU coaster blanks.. Both the rounds and the squares. I am having some problems when I do fills in that the edge tends to bleed resin, which makes cleanup and sanding almo...

• laser engraving

Henry

2025-12-10

820

4

2

Hi, Is there anywhere in the lasergrbl program that shows the current line being burned or the line that was being burned when an error occurs? I have had a few times where the laser has stopped and I...

• laser engraving

Terrelle

2025-12-05

2.6K

1

0

Some of my pictures (letters) are not filled in. The enlarged image shows that the lines are closed, but in reality, the lines only appear intermittently and are not fully filled. In the same file, so...

• laser engraving

Kevin

2025-12-01

872

2

1

Why do the lines I get always bend? Whether I use vectorization or any other settings, the lines are never perfect. I saved them in PNG and JPEG formats, but the problem persists.

• laser engraving

Miller

2025-11-28

826

2

0

I have a 50W CO2 laser cutting and engraving machine, and recently I purchased a laser power meter. I need to develop a measurement program on how to use the laser power meter. Here is my plan. •Ensu...

• laser engraving
• laser cutting

Abel

2025-11-28

1.1K

5

1

Will the water temperature flowing through the laser tube have a direct impact on the laser ablation efficiency? I know the water temperature should not exceed 70 degrees Fahrenheit, but is there a li...

• laser engraving

Smith

2025-11-24

624

1

0

Laser engraving on wood is not only about engraving images, but also endowing natural wood with artistic life. Mastering the essence of it can create works that even experienced craftsmen can admire. ...

• laser engraving

roy

2025-11-21

658

0

0

I need some help, see pic. I want to engrave this image just like it is but how do I do that with part of 1 image on top of the other? I want the gate to look like it’s in front of the house with a li...

• laser engraving

jessie

2025-11-20

630

1

0

I have an AtomStack 5 (5W) and GRBL software. When I turn on the laser to find the center point of a circular wooden block, the laser burns the wood before starting carving. Does anyone know the reaso...

• laser engraving

Aaron

2025-11-14

685

3

0