So when I engrave or cut the laser moves to the same position it starts from. When I use the rotary and engrave tumblers the laser head goes to a differant position from where it starts. This has changed since I upgraded from 1.6 to 1.7.01. How do I change so laser head parks after engraving in the same position it starts?

Noah

2024-10-11

993

3

0

Hello,I am using version 1.7.00 in English, down loaded SHX fonts from Internet, extracted to a folder, put the folder name in configuration SET SHX font path, it does not bring the SHX fonts when I type over default arial a font like “FIN”, simply it cannot find it. Any clue?

Ethan

2024-10-11

831

4

0

hello everyone,I found an example of PCB design online. In practice, the base is painted black and the paint burns out in areas where copper must be removed through reverse circuit design. Then etch with acid.The laser head must be installed on the CNC instead of the spindle, but I don't know the power and cost of this instrument.Is one of these la...

Ruddy

2024-10-14

689

1

0

I have a J-Tech Photonics 4.2-watt laser. My current value setting is 1000.My question is, what would happen if I increased each setting equally, how would this effect my laser?

Rajiv001

2024-10-12

875

1

0

I have been installing S9 for a few months now, and a few days ago I decided to give it a try.I returned to my original position, but strangely, the machine got stuck after traveling a few centimeters. I exerted a little force, and it traveled a few more centimeters before locking again.I think the strap may be too tight, so I patiently loosened it...

Rajiv001

2024-10-09

1K

2

0

I built a project and set the cuts/layers speed to 10 and saved the project. I then reselected the project and loaded to the art library. When I bring the project from the art library to the workspace the speed in cuts/layers has changed. I’m using Lightburn 1.7.01 on a windows 10 laptop.

Erdogan

2024-10-10

935

1

0

Mac Ventura, lightburn 1 6 03 neje max 4Never had this problem before upgrading to lightburn1.6.03when engraving, which is most of my workflow, the laser starts each line 2mm to the left of the last, so quickly runs off the wood I am engraving. Sometimes if I rotate the engraving 90 degrees it engraved okay but id I duplicate back to the same issue...

さいと康成

2024-10-10

807

1

0

Hi,after installing the new version 1.7.01 the laser freezes when it has to draw a curve or an image and returns this error:The format of the numeric value is invalid or an expected value is missing.On or near line 0:No problems so farcan someone help me?thanks

RTP

2024-10-08

712

2

0

Why? Line nodes won’t connect to other nodes? What is the trick? And why did the nodes on a new line turn all red?

Roderick

2024-10-08

809

2

0

We are setting up a laser machine to carve copper; From the first test, for example, by digging a small square at 0 degrees, a Z-dip angle of approximately 10-15 degrees can be obtained. What parameters should we use for perfect straight line cutting?

55455rml

2024-10-09

714

1

0

Is there a way to set the machine to only engrave over the parts that are being engraved instead of the machine spanning the whole piece I’m trying to cut an engrave.5 hours to engrave and cut these hexagons.10 min to cut and engrave one single one70 min if I did them each individuallywould be a cool feature if you could engrave each location ins...

Carey

2024-10-03

723

2

0

new 1.7.01 update leaves off fill on screenno longer shows difference between line and fill when viewing file you have to hit the preview to see the difference

Silvano

2024-10-05

784

2

0

I am trying to cut the hexagon out, take that piece out of the material it was cut from, bevel the edges, pop it back in the same spot it came from, and then engrave it so that it engraves the edge of the angle.The only way I can figure out how to do this. is if I delete the engraved part, cut the hexagon out, leave the material in place, take it ...

Cruise Wang

2024-10-03

743

2

0

Im new to laser cutting / engraving so please forgive my ignorance . I have been told to use a coolant for my laser cutter . Can any of u legends give some helpful advice on the coolant i should use ?

JOST

2024-10-05

779

1

0

I have this color logo from my Gasparilla Krewe, I have tried engraving this a couple times but it just not coming out to my liking, I have converted to black and white but still doesn’t looks good. Any suggestions?

LWE

2024-09-30

876

1

0