I have a CO₂ laser cutting machine equipped with a Ruida RDC8445S controller. After booting up, it gets stuck in the loading interface and cannot start. How to solve this problem?

• RDC8445S
• control system
• RuiDa

seek help! Where can I download the mobile control software for RDC8445S controller?

• RDC8445S
• RuiDa

Hello everyone! I have another question to ask, regarding the RDC8445S control system. I have noticed that the positioning function on the panel is not functioning properly. Every time the positioning...

• RDC8445S
• control system
• CO₂ laser
• RuiDa

When using the RDC8445S laser controller, I found that the laser output is very weak and cannot achieve the expected light intensity. Meanwhile, when I tried to adjust the light control function on th...

• RDC8445S
• control system
• CO₂ laser
• RuiDa

My device uses the RDC8445S control system. Today, when I was processing, I set the U-axis to the rotation axis, but the original multi-point positioning function of the device cannot be used properly...

• RDC8445S
• control system
• CO₂ laser
• laser cutting
• RuiDa

Hello Ruida Support, We have two laser machines using Ruida RDC6445S controllers connected to the same local network. Machine 1 works perfectly under the same conditions, using the same computer, soft...

• RDC8445S

Hello everyone, I’m reaching out to the community for a technical perspective, as I’m facing a recurring issue and have not yet been able to identify the root cause. Here is a clear summary of the s...

• RDWorksV8
• RDC8445S
• RDC6445G
• control system

When using the RDC8445S controller, I tried to connect to the computer via USB, but the system still couldn't recognize the driver. Trying to change ports and restart the system, the problem persists....

• USB
• RDC8445S
• control system
• RuiDa

estoy instalando por primera vez una tarjeta RUIDA RDC8445S y tengo problemas ya que el administrador de dispositivoa la reconoce y le asigna un puerto com pero al instalar el software no la reconoce...

• RDC8445S

I found an abnormality in the motherboard during routine equipment inspection of the RDC8445S control system. The panel originally used to control laser engraving and cutting cannot start, and the scr...

• power supply
• RDC8445S
• laser engraving
• laser cutting
• RuiDa

Today, I used CO2 laser cutting equipment to process workpieces. The control system is RDC8445S. After starting, the cutting head ran normally, but there were obvious uncut areas on the edges of the c...

• galvo scanner
• beam delivery system
• RDC8445S
• laser head
• RuiDa

My CO2 laser cutting machine uses the RDC8445S control system. Today, I found an abnormality while operating it. Every time the processing program starts, the originally set processing point will auto...

• power supply
• RDC8445S
• control system
• CO₂ laser
• RuiDa

I encountered a problem today, the power indicator light of my RDC8445S controller suddenly stopped working. Normally, this indicator light should be on to display the power status of the controller, ...

• power supply
• RDC8445S
• control system
• RuiDa

My device is paired with the RDC8445S control system, and what confuses me is that the machine can only move in one direction, and no matter how I adjust the input signal, the machine never responds t...

• motion system
• RDC8445S
• control system
• CO₂ laser
• RuiDa

When using the RDC8445S controller for scanning, I found that the scanning results always showed ghosting. I checked the controller settings, adjusted the resolution and scanning speed, but the proble...

• galvo scanner
• RDC8445S
• control system
• CO₂ laser
• RuiDa