- Rozwiązane
My laser welding system RDWelder DW-V2Pro has abnormal light output
My handheld laser welding system is RDWelder DW-V2Pro. Although the equipment can start normally, the laser output is significantly abnormal and the energy is significantly reduced compared to before....
- galvo scanner
- beam delivery system
- RDWelderDW-V2Pro
- laser welding
- RuiDa
- 3 użytkowników odpowiedziało
165 - Rozwiązane
Why can't the RDC8445S controller cut through?
Today, I used CO2 laser cutting equipment to process workpieces. The control system is RDC8445S. After starting, the cutting head ran normally, but there were obvious uncut areas on the edges of the c...
- galvo scanner
- beam delivery system
- RDC8445S
- laser head
- RuiDa
- 2 użytkowników odpowiedziało
217 - Rozwiązane
RDWelder-SW handheld welding system cannot be connected properly
When I was operating the RDWelder-SW handheld welding system, the device was unable to connect properly. After turning on, communication cannot be established between the control panel and the welding...
- beam delivery system
- RDWelder-SW
- laser head
- laser welding
- RuiDa
- 3 użytkowników odpowiedziało
201 - Rozwiązane
Laser handheld welding RDWelder-SW has abnormal light output
I tried to seek help in this community by starting a laser handheld welding machine equipped with an RDWelder-SW controller. The parameters were not changed, and the gas and water cooling were also no...
- galvo scanner
- beam delivery system
- RDWelder-SW
- laser welding
- RuiDa
- 3 użytkowników odpowiedziało
215 - Rozwiązane
How to solve the problem of uneven carving bottom in RDC8445S control system?
I used the RDC8445S control system for carving and found that the bottom of the carving was uneven. After careful inspection, I found that this problem occurred in different areas, especially in large...
- galvo scanner
- assist gas system
- beam delivery system
- RDC8445S
- RuiDa
- 1 użytkownik odpowiedział
228 - Nie rozwiązane
How to solve the problem of insufficient laser engraving depth in RDC6585G controller?
I operate a CO2 laser engraving machine for engraving, with the control system being RDC6585G. The light intensity and speed settings meet conventional requirements, and the engraved patterns and text...
- power supply
- beam delivery system
- RDC6585G
- laser engraving
- RuiDa
- 1 użytkownik odpowiedział
219 The processing method for frequent temperature control alarms caused by short-term heating in laser handheld welding
When using laser handheld welding equipment, if the welding effect is abnormal and the temperature control alarm is frequent due to short-term heating, the following steps can be followed to troublesh...
- beam delivery system
- laser head
- control system
- laser welding
- RuiDa
Adrian21612Solution for RDM5020CL-T70 cleaning with no red light and burning protective lenses
If there is an abnormal situation where the RDM5020CL-T70 cleaning system does not produce red light and burns out the protective lens, the following steps can be followed for troubleshooting and hand...
- beam delivery system
- RDM5020CL-T70
- laser head
- laser cleaning
- RuiDa
Thomas22602- Rozwiązane
When using RDWorksV8 for cutting, the graphic font becomes skewed
When I was using RDWorksV8 for cutting today, I imported the file and everything was normal. However, when I cut it out, I found that the font had an unexpected skew. I checked the relevant parameters...
- beam delivery system
- RDWorksV8
- laser cutting
- RuiDa
- 3 użytkowników odpowiedziało
283 The handheld laser welding system shows that it cannot connect properly and does not emit light for welding
When using handheld laser welding systems RDWelder-SW and RDWelderDW-V2Pro, if the display shows that the connection cannot be made properly and the welding does not produce light, you can follow the ...
- beam delivery system
- RDWelderDW-V2Pro
- RDWelder-SW
- laser welding
- RuiDa
Darren30611Laser cutting wood, what if it's not cut through?
When using the CO₂ laser cutting series control system, if you encounter a situation where the material cannot be cut through, you can follow the steps below to troubleshoot and make improvements: 1....
- galvo scanner
- beam delivery system
- laser head
- CO₂ laser
- RuiDa
John Trant29500Five major factors teach you how to choose CO2 laser
The laser source is the heart of a laser machine and plays a decisive role in cutting quality. A good laser source should have an ideal beam mode, stable power output, and reliable performance. There ...
- beam delivery system
- laser source
- CO₂ laser
- laser cutting
WernerVogel34425- Rozwiązane
RDWelder DW-V2Pro, my handheld welder has very weak light output
My handheld welding machine has been in use for several months now. It uses the RDWelder DW-V2Pro control system. Today, while performing routine operations as usual, I noticed the laser output is ver...
- galvo scanner
- beam delivery system
- RDWelderDW-V2Pro
- laser welding
- RuiDa
- 2 użytkowników odpowiedziało
291 - Rozwiązane
RDWelder SW handheld laser welding generates frequent heating and temperature control alarms
Just bought equipment, handheld laser welding, RDWelder-SW， I tried welding, but the welding effect was not normal. The welding process heats up quickly and the temperature control alarm is frequent. ...
- beam delivery system
- RDWelder-SW
- laser head
- laser welding
- RuiDa
- 3 użytkowników odpowiedziało
303 The influence of key components of laser cutting machine on cutting accuracy
Why is precision so important in laser cutting? The core of laser cutting lies in achieving clean, sharp, and precise cutting effects. Whether it is metal materials for automotive components or acryl...
- motion system
- beam delivery system
- laser head
- control system
- laser cutting
Darren33612
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.