- Niet opgelost
How to set up rotating attachments in RDworks?
I'm looking for step-by-step guidance on setting up a rotary attachment in RDWorks. The rotary is spinning, and I've tried changing the steps and diameter values, but the outcome remains unchanged. Am...
- rotate
- RDWorksV8
- RuiDa
- 1 gebruiker beantwoord
57 - Opgelost
RDD6584G control system punch does not rotate
I found that the punch cannot rotate while operating the RDD6584G control system. The system is powered on normally and there are no alarms on the display interface, but the punch does not respond aft...
- rotate
- RDD6584G
- control system
- RuiDa
- 2 gebruikers beantwoord
239 - Niet opgelost
How to set the rotation of Lasergrbl?
I initially used LaserGRBL, but I am not familiar with many operations. After opening the software, I searched for the rotation function on the interface, but the operation steps were not very intuiti...
- rotate
- LaserGRBL
- laser engraving
- 1 gebruiker beantwoord
198 - Niet opgelost
RDC8445S controller, why can't the multi-point positioning function be used?
I have a CO2 laser cutting machine and I found that the U-axis cannot use the multi-point positioning function properly when working as a rotating axis. Whenever I try to set multiple positioning poin...
- rotate
- coordinate axis
- CO₂ laser
- RuiDa
- 1 gebruiker beantwoord
234 - Niet opgelost
RDWorksV8， Method for calculating circumferential pulse parameter values in rotary engraving
Hello everyone! How do I calculate the circumferential pulse parameter value for rotary engraving using RDWorksV8? Thanks in advance!
- rotate
- RDWorksV8
- laser engraving
- RuiDa
- 1 gebruiker beantwoord
289 - Opgelost
What is the calculation method for using rotation specific step sizes as rotational engraving in RDWorksV8?
When using RDWorksV8 for rotary engraving, I chose "rotation specific step distance" as the calculation method. How do I calculate it? Please provide a detailed explanation, thank you!
- rotate
- RDWorksV8
- laser engraving
- RuiDa
- 1 gebruiker beantwoord
219 - Niet opgelost
RDD6584G controller, how to calculate pulses?
My vibrating knife cutting system is RDD6584G. I have a simple question, how do I calculate the pulse?
- rotate
- RDD6584G
- RuiDa
- 1 gebruiker beantwoord
203 - Opgelost
RDC8445S controller multi-point positioning function cannot be used
My cutting machine uses a ruida controller, RDC8445S， I set the U-axis as the rotation axis for cylindrical machining, but I found an issue: once the rotation axis mode is enabled, the normal multi-po...
- rotate
- coordinate axis
- RDC8445S
- control system
- RuiDa
- 2 gebruikers beantwoord
238 - Opgelost
In RDWorksV8, the brush function uses the Z axis instead of the U axis for rotating surface machining, resulting in an idle reset
I am using the brush function in RDWorksV8 for rotary machining, intending to have the Z axis replace the U axis to complete continuous machining of the rotary surface. After downloading the file and ...
- rotate
- coordinate axis
- RDWorksV8
- RuiDa
- 3 gebruikers beantwoord
260 - Opgelost
The punch of the RDD6616U vibrating knife does not rotate,what's the reason?
My vibration knife controller is RDD6616U. Today, when I was operating the machine for processing, the equipment could move normally, and the vibration knife could move up and down, but the punch head...
- rotate
- RDD6616U
- control system
- RuiDa
- 2 gebruikers beantwoord
257 - Opgelost
In the RDC6442G controller, the multi-point positioning function cannot be used when the U-axis rotates
My controller is RDC6442G. I set the U-axis as the rotation axis and found that the multi-point positioning function cannot be enabled. No matter how I adjust the software parameters, the system still...
- rotate
- coordinate axis
- RDC6442G
- control system
- RuiDa
- 1 gebruiker beantwoord
237 - Opgelost
seek help! RDD6584G， Abnormal rotation angle
I am using the RDD6584G vibration knife control system. After setting the rotation axis pulse, I found that the rotation angle is abnormal. I don't know how to handle it? Please seek guidance from pro...
- rotate
- RDD6584G
- RuiDa
- 2 gebruikers beantwoord
284 What should you do if RDWorksV8 cannot perform rotary cutting?
What should I do if I am unable to perform rotary cutting when using RDWorksV8 for machining? Follow the following methods to troubleshoot and resolve: 1. Disable Rotary Engraving Function Rotary eng...
- rotate
- coordinate axis
- RDWorksV8
- laser cutting
- RuiDa
Marshall28300RDWorksV8， The relationship between circumferential pulse and workpiece diameter in rotary engraving
Procedure 1. Calibration: Use a workpiece with a known circumference (e.g., diameter 31.84mm, circumference 100mm) for calibration. Adjust the driver parameters or software settings so that when this...
- rotate
- RDWorksV8
- laser engraving
- RuiDa
roy32600How to measure or calculate the circumferential pulse parameter values for RDWorksV8 rotary engraving?
Step 1: Consult Official Specifications Obtain accurate parameters from the stepper motor drive or rotary axis manufacturer. Key Parameters: Stepper motor step angle (e.g., 1.8°), drive microsteppin...
- rotate
- RDWorksV8
- laser engraving
- RuiDa
Gilbert32810
rotate
25
Onderwerpen3
VolgersWacht op antwoorden
- RDworksV8可以加工锤子画吗？
- Where can I download the firmware upgrade file for the RDC6445 series controller?
- After installing the RDWorksV8 plugin in CorelDRAW, how can I do engraving and cutting at the same time?
- Edge tracing for contour cutting
- How do I adjust the time displayed on the C320？
- problema na cnc
- Mantisoft User guide or Manual
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.