- Niet opgelost
Why does the RDV6445G controller have a deviation in cutting the cross?
Hello everyone, I have encountered a new problem again, RDV6445G， The cross shaped pattern cut always has deviations, and the distance of deviation varies greatly, making it difficult to fix. I checke...
- motion system
- RDV6445G
- control system
- RuiDa
- 2 gebruikers beantwoord
215 - Opgelost
Why does the RDV6445G controller experience missed mark detection?
My CO2 vision cutting equipment is paired with the RDV6445G control system. During vision positioning, I've encountered instances where mark points are either misidentified or not recognized at all. A...
- camera
- CO₂ visual cutting
- RDV6445G
- control system
- RuiDa
- 2 gebruikers beantwoord
208 - Opgelost
RDV6445G controller calibration failed
Hello everyone! I am adjusting the CO2 visual cutting equipment, and the control system is RDV6445G. During the calibration process, the equipment cannot respond correctly to the set parameters, causi...
- CO₂ visual cutting
- RDV6445G
- control system
- RuiDa
- 2 gebruikers beantwoord
246 - Opgelost
Why can't the RDV6445G control system recognize the camera USB driver?
My CO2 vision cutting machine uses the RDV6445G controller. Today, when I was debugging, I found that the system could not recognize the device properly after connecting the camera through the USB int...
- camera
- USB
- CO₂ visual cutting
- RDV6445G
- RuiDa
- 2 gebruikers beantwoord
240 - Opgelost
CO2 Visual Cutting Control System RDV6445G Field of View Display Incorrect
My CO2 laser cutting system is experiencing another issue. The RDV6445G's field of view display is incorrect. The image that should precisely show the cutting area is offset, making it impossible to a...
- CO₂ visual cutting
- RDV6445G
- control system
- RuiDa
- 2 gebruikers beantwoord
212 - Opgelost
How to solve the distance limit of the pop-up box after the RDV6445G controller's mark point recognition is completed?
Hello! I think I should look for more help in this community. During the operation of my CO2 visual cutting system RDV6445G, I identified mark points according to the predetermined process. However, a...
- CO₂ visual cutting
- RDV6445G
- control system
- RuiDa
- 2 gebruikers beantwoord
237 - Opgelost
How to solve the problem of R100 camera not displaying in RDV6445G?
I encountered a problem while using the RDV6445G controller for visual processing. The system has recognized the R100 camera, but the screen still cannot be displayed after entering the visual interfa...
- camera
- CO₂ visual cutting
- RDV6445G
- control system
- RuiDa
- 2 gebruikers beantwoord
253 - Opgelost
RDV6445G Controller Y-Axis Not Homing, X-Axis Homing Causes Collision
My CO2 laser cutting machine uses a Ruida controller, model RDV6445G. I encountered two issues today. The Y-axis cannot be reset, and during the X-axis reset process, it keeps moving forward, eventual...
- coordinate axis
- CO₂ visual cutting
- RDV6445G
- control system
- RuiDa
- 2 gebruikers beantwoord
266 - Opgelost
How to solve the error reported when taking photos in the RDV6445G visual control system?
I am not familiar with the operation of the Ruida controller. When I was conducting positioning debugging for my visual control system RDV6445G, an error message appeared after entering the photo func...
- camera
- CO₂ visual cutting
- RDV6445G
- control system
- RuiDa
- 4 gebruikers beantwoord
278 Reasons for Inability to Adjust Camera Exposure in CO2 Visual Cutting Control System
In the CO2 Visual Cutting Control System, such as the RDV6445G and RDV6332M, if issues arise where camera exposure cannot be calibrated, the causes can be attributed to the following two aspects: Cam...
- camera
- CO₂ visual cutting
- RDV6445G
- RDV6332M
- RuiDa
Michael23201Solution to corner processing problems in CO2 visual cutting control system
During the processing using the CO2 visual cutting control system (models: RDV6445G, RDV6332M, RDC6685U-DFM, RDC6445GZ-DFM-RD), the overall contour is basically accurate. However, if there are abnorma...
- CO₂ visual cutting
- RDC6685U-DFM
- RDV6445G
- RDV6332M
- RuiDa
Gary22400What should you do if the template file of the CO2 visual cutting control system cannot be displayed?
When using the CO2 visual cutting control system (RDV6445G, RDV6332M, RDC6685U-DFM, RDC6445GZ-DFM-RD), if there is a situation where the template file cannot be displayed or the template is lost, it c...
- RDC6445GZ-DFM-RD
- RDC6685U-DFM
- RDV6445G
- RDV6332M
- RuiDa
Spark28624How to solve the cross deviation of RDV6445G small visual cutting?
When using the RDV6445G small vision control system for cross cutting, if there is a cross deviation and the distance is not fixed, it can usually be checked from the following two aspects: 1. Check ...
- motion system
- RDV6445G
- control system
- RuiDa
Ignativs24001The mark point of the CO2 visual cutting system is not recognized，what should you do?
During the processing of the CO2 visual cutting system, there may be occasions where the Mark points cannot be identified or are omitted. Generally, the following two steps can be taken to troubleshoo...
- camera
- CO₂ visual cutting
- RDV6445G
- RDV6332M
- RuiDa
Ignativs24301CO2 visual cutting control system, CCD software camera parameter debugging
When using the CO2 visual cutting control system for machining operations, how do I debug the CCD software camera? 1. Enter the camera parameter interface Open the CCD software and click“Camera Param...
- camera
- CO₂ visual cutting
- RDV6445G
- RDV6332M
- RuiDa
Adrian26101
RDV6445G
22
Onderwerpen10
Volgers
Wacht op antwoorden
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.