What have you done so far to accommodate the change in size?There are likely 2 things that need to be changed:1. Workspace size in LightBurn Edit->Device Settings. Note that you’ll want to express this in terms of width x height so 400x850 mm.2. Change of $131 value to $131=850 in Edit->Machine Settings.

Cyril

2023-03-13

743

0

0

is there a simple setting for when you rotate text 90 degrees? can i switch the scan direction to move y axis first then the x? when i rotate the text, and there is space between lines, the laser has to travel across those blank spaces just to make one small tick, then move on. seems would be faster to scan across the line of text rather than up/do...

Simon

2023-03-10

741

1

0

Hi guys,I’ve been using Lightburn for some time now with my 50w JPT Fiber laser.I’ve just recently installed and setup my rotary, my problem is once I have successfully setup the rotary for the current project and run project, then saved it for multiple runs. I then create a new project which requires a different rotary config, set tha...

Jen

2023-03-10

788

1

0

I have a project where I have to burn off black paint from a plexiglass. (a transparent scale for a tank with liquid) I got a sheet of transparent, fully clear, not matte, plexiglass (acrylic glass) I spray painted it with black paint (have two choices, from a spray can, of can use an airbrush and paint it with water based acrylic paint, same resul...

John Trant

2023-03-10

699

1

0

Hello, i am making an offset on a fairly large circle and the offset isnt round (even after selecting the round option) is there a setting i have wrong?also, how can i make my nodes so that i can round them out?

Robert Evans

2023-03-10

599

1

0

In Art Library window there’s an “Import” button. Push that, you can then choose multiple files to import. I’m not sure if there’s a practical limit to how many can be selected.I’ll caution that even if something is packaged as an SVG that it may not really be in laser ready form. Even purchased SVGs may be of lo...

Henry

2023-03-10

686

1

0

Does Lightburn save the calculated cut path optimizations in the file? Can it? Or, does it have to recalculate them every time I run the file? I’m on LB 1.3.01 on Ubuntu 22.04.

Jamie

2023-03-10

769

1

0

The can is broken, and the pressure is rhythmic. This is the hydraulic part.On the other hand, the servo motor follows the rhythm of the energy storage tank and goes off and on.Oil and electricity are irrelevant.

Keegan

2023-03-10

767

1

0

In the process of equipment debugging, it was found that the servo motor could not reach the specified position. After troubleshooting, it was found that there was a problem with the IO line of the driver. It would be good if it was replaced. The servo motor uses position control, and the command pulse sent by PLC will be lost due to the poor conta...

Marshall

2023-03-10

860

1

0

Spiral gear is a common mechanical transmission device, which is widely used in various industrial equipment. Compared with other gears, helical gears have certain advantages, such as gradual contact, gradual departure, low noise, strong transmission capacity, etc. The following describes the advantages and applications of some helical gears.&nbsp...

Tory

2023-03-10

576

0

0

As the annual event of the laser, optical and optoelectronic industries in Asia, the 17th Munich Shanghai Optical Expo will be held at 6.1H, 7.1H and 8.1H of the National Convention and Exhibition Center (Shanghai) from July 11 to 13.After two years, exhibitors have an unprecedented enthusiasm for registration, and the exhibition area will ...

David

2023-03-10

595

0

0

The cutting drawing is not closed, and there is no problem with the drawing. How to solve this problem?

Jen

2023-01-09

733

2

0

A series of problems will occur in the transmission process of gears. There are many kinds of gears. The general structure of gears includes gear tooth surface, normal surface, tooth top circle, tooth groove, end face, tooth root circle, base circle, scale circle, plastic deformation of tooth surface that may occur in gear transmission, gear fractu...

Patrick

2023-03-09

686

1

1

Getting cannot find C:\lbexport.aiCant find fix

Payson

2023-03-09

819

1

0

Trying to get Lightburn to work with my fiber laser, can’t get it to find the laser. tried several time to load the driver and it still won’t work. There is a pic of the board that’s in my machine. Can anyone help, Thanks Ron

Terrelle

2023-03-09

774

1

0