Can Lasergrbl be used for carving and cutting in the same project?My machine is a 10W laser

Christian

2日前

58

2

0

I am preparing to carve slate. Before that, what pigment should I use to color the slate？

David

1日前

37

1

0

During the use of laser cutting machines, it is inevitable to encounter various problems, which can lead to unsatisfactory processing results. Here are 10 common problems that cause laser cutting failures.1. Contaminated Protective LensesTouching protective lenses with bare hands or neglecting to clean off dust can significantly reduce their tran...

Gilbert

1時間前

3

0

0

1. Can diode laser cutting cut transparent acrylic?After fine adjustment of relevant parameters, the diode laser (≥ 30 W) can cut transparent acrylic with a thickness of about 6 millimeters.Laser PowerUse 65–70 % of the diode’s peak output to balance cut quality and speed.Cutting SpeedAim for 5–8 mm/s: slower speeds risk excessive melting; faster...

Payson

1日前

34

0

0

I am looking for the best diode laser between $2000 and $3000. Reliability, usability, support, and functionality are all important.

Cyril

10-25

94

2

0

The weather is getting colder day by day, and machines and equipment, like humans, need to be kept warm. The following article introduces the key points related to antifreeze for laser cutting machines.1.Do not turn off the chillerAfter the laser cutting machine is not working, do not turn off the water cooler when ensuring that the power supply w...

Darren

2日前

67

0

0

Laser cutting of thick steel plates has become a part of daily manufacturing, but laser cutting of thick plates still faces some challenges: energy must penetrate deeply, molten material must be cleanly discharged, and the cutting edge must remain stable over long distances. The following are the main challenges faced by the workshop and mature sol...

Miller

10-22

120

2

1

Myth 1: High equipment costsReality: Although the initial investment in a laser tube cutting machine may seem substantial, the long-term operational costs can be competitive compared to other cutting methods. Laser tube cutting machines offer high efficiency, minimal material waste, and reduced setup times, resulting in lower overall production cos...

jessie

3日前

79

0

0

NEJE MAX 4 V2 E80， Equipped with Z-axis stepperI am trying to set lightburn so that when I input the material thickness, the z-axis will move to make it in focus.I have set the G54 z offset to -17, which is the focused position on the machine tool.When lightburn runs, it raises the z-axis to the height of the material, placing it in focus.My questi...

Henry

10-24

89

1

0

In general, the most direct way to improve processing efficiency is to increase the laser power. When the 60000 watt laser cutting machine was launched, it sparked discussions.Industry experts believe that 60000 watts have the ability to fully replace plasma and flame cutting. Further increasing power does not contribute significantly to cutting e...

Robert Evans

10-25

98

0

0

I am getting a buffer message after pressing the start button. How do I clear it?

Tory

10-21

136

3

1

I use a rotating tool, when engraving the inner pattern engraves perfectly. When it goes back to do the outline it is off by a MM or 2 in one area and further in another area on the pattern. I don’t know if it is a setting issue or mechanical issues with my equipment.

David

10-23

86

1

0

Fiber lasers have the advantages of high precision, efficiency, and versatility, and are widely used in industries such as manufacturing, construction, and packaging. So, what materials can fiber lasers cut?Metal Materials1.Stainless SteelFiber laser cutting excels in processing stainless steel, achieving remarkable cutting depths of up to 0.75 i...

Williams

10-24

110

0

0

What is the best method to carve a white effect on glass using a 10W diode? What is the best way to achieve similar results using fast, high-power, low-speed, and low-power?

Nugent

10-22

92

1

0

1. Diagonal cutting of metal pipesDiagonal cutting on metal pipes usually refers to oblique cutting at the edge of the pipe, rather than vertical (90 degree) cutting. Diagonal cutting is usually done at a 45 degree angle, but can also be adjusted to other angles depending on the application. This cutting method can achieve precise connections, espe...

Darren

10-23

125

0

0