- Risolto
Using RDWorksV8, the servo motor only moves in one direction
I am operating the device using RDWorksV8, but the servo motor only moves in one direction. I searched online and found information that it is a wiring issue. Is that correct?
- motion system
- RDWorksV8
- RuiDa
- 2 utenti hanno risposto
305 - Risolto
I am using the RDC6563FG control card, but there is shaking when the laser head moves with it
I encountered another problem today. My device is equipped with an RDC6563FG control card, but when the laser head moves, it shakes. I don't know if it's due to poor contact or capacitor calibration. ...
- assist gas system
- motion system
- RDC6563FG
- RuiDa
- 3 utenti hanno risposto
308 - Risolto
RDC6332NM switches to manual mode, and the Z-axis motor remains stationary
I switched to manual mode and pressed the Z+and Z - buttons on the control panel, but the Z-axis motor did not move. The model is RDC6332NM， How to solve it?
- motion system
- coordinate axis
- RDC6332NM
- laser cutting
- RuiDa
- 3 utenti hanno risposto
359 The influence of key components of laser cutting machine on cutting accuracy
Why is precision so important in laser cutting? The core of laser cutting lies in achieving clean, sharp, and precise cutting effects. Whether it is metal materials for automotive components or acryl...
- motion system
- beam delivery system
- laser head
- control system
- laser cutting
Darren33512- Risolto
RDC6563FG: XY axis does not move in manual mode
My fiber laser cutting machine has changed its control card: RDC6563FG. Today, when I was operating it in manual mode, the XY axis did not move. I know this is a typical motion control problem, so how...
- motion system
- coordinate axis
- RDC6563FG
- RuiDa
- 2 utenti hanno risposto
351 Using LaserGRBL, The movement speed of the laser engraving machine is too slow
Set a speed in LaserGRBL, but engraving occurs at slower speeds. During processing LaserGRBL always command the speed you requested. However, there are reasons why the engraver may move slower. The f...
- motion system
- LaserGRBL
- laser engraving
Patrick33700- Risolto
Help, RDC6563FG, Z-axis cutting head not moving
I am operating the machine and the control card is Ruida, model RDC6563FG, I manually move the Z-axis on the panel, but the cutting head doesn't move. Is it a problem with the servo drive?
- motion system
- coordinate axis
- RDC6563FG
- RuiDa
- 2 utenti hanno risposto
388 - Risolto
RDC6332NM cutting head automatically searches for focus and moves downwards continuously
My machine is equipped with RDC6332NM, and the cutting head automatically focuses or moves downwards at any time. How can I solve this problem?
- motion system
- RDC6332NM
- laser head
- laser cutting
- RuiDa
- 2 utenti hanno risposto
415 RDC6612U how to input alarm from servo driver to mainboard
Hello, Can someone support me with connect alarm info from servo driver to ruida main board ? It should works as below: If some error exist on driver, then I have info on operation panel, and workin...
- motion system
- RDC6612U
- control system
- RuiDa
2E66B82966430The equipment cannot return to the positioning point after processing
Fault analysis: 1. Enable multiple positioning points 2. Failed to locate successfully 3. Panel button malfunction 4. Return setting error Solution: Upon checking the user parameters, it was found t...
- motion system
Marshall1.3K00Excessive vibration during operation of three-phase asynchronous motor
Possible causes of malfunction: Excessive clearance of bearings due to wear and tear; Uneven air gap affects the balance of the motor; Unbalanced rotor leads to vibration; The bending deformation of t...
- motion system
Henry1.4K00Detailed explanation of DC brushless motor faults
With the development of the industrial industry, brushless DC motors, as a commonly used type of electric motor, have become increasingly widely used due to their high efficiency, high speed, and low ...
- motion system
Cyril1.4K00Analysis of common problems with brushless DC motors
1、 Motor burnt out One of the common faults of brushless DC motors is motor burnout. Possible reasons include overvoltage, overload, overheating, etc. If the motor is found to be burnt out, it is nece...
- motion system
roy1.6K10The curve is not good. Why is that?
I get very bad curves. Belts are tight. What else happens? Is this normal from the stepper motors or something i have to check? Thanks in advance
- motion system
- laser cutting
Andrej1.4K20Alarm 6, the stepper is stuck and unable to move. Is the stepper broken?
hello i havent used my 3018 in a while and am wondering what im doing wrong. i’m all set up wit grbl and lightburn 1.7.03 I power up and it begins to home motors just stuttuer terribly and wont move.h...
- motion system
- LaserGRBL
- LightBurn
Jack Wilborn1.3K10
motion system
82
Argomenti5
FollowerIn attesa di risposte
- RDworksV8可以加工锤子画吗？
- Where can I download the firmware upgrade file for the RDC6445 series controller?
- After installing the RDWorksV8 plugin in CorelDRAW, how can I do engraving and cutting at the same time?
- Edge tracing for contour cutting
- How do I adjust the time displayed on the C320？
- problema na cnc
- Mantisoft User guide or Manual
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.