How to control the stepper motor to realize intermittent feed motion by xinjie plc.
2023-03-131.1K10I’m making a small drawstring bag.I created a rectangle 100mm x 140mm. I then put a radius of 50mm on the bottom 2 corners making a cup or shield sort of shape (rounded bottom of the bag). Then I created a tool layer (T2) by using the Offset Shapes tool and shrinking by 4 to create my stitch line. Using the Edit Nodes tool, I deleted the top...
2023-03-1397410Lightburn up to date 1.3.01 and now the laser when framing is going ballistic grinding and not framing right. I have projects to do on a time line and if Lightburn will not run when I need it maybe I need to find another software.
2023-03-131.3K10My laser burns some extra lines in text. Using Genmitsu 3018 router with laser attachment.
2023-03-131.1K10One equipment on the production line and one servo are transplanted to the normal position. It has been determined that there is no problem with the mechanism. It should be an interference problem. The servo is Panasonic servo motor. I don't know how to eliminate this problem?
2023-03-131.1K10is there a simple setting for when you rotate text 90 degrees? can i switch the scan direction to move y axis first then the x? when i rotate the text, and there is space between lines, the laser has to travel across those blank spaces just to make one small tick, then move on. seems would be faster to scan across the line of text rather than up/do...
2023-03-1098410Hi guys,I’ve been using Lightburn for some time now with my 50w JPT Fiber laser.I’ve just recently installed and setup my rotary, my problem is once I have successfully setup the rotary for the current project and run project, then saved it for multiple runs. I then create a new project which requires a different rotary config, set tha...
2023-03-101.1K10I have a project where I have to burn off black paint from a plexiglass. (a transparent scale for a tank with liquid) I got a sheet of transparent, fully clear, not matte, plexiglass (acrylic glass) I spray painted it with black paint (have two choices, from a spray can, of can use an airbrush and paint it with water based acrylic paint, same resul...
2023-03-101.1K10Does Lightburn save the calculated cut path optimizations in the file? Can it? Or, does it have to recalculate them every time I run the file? I’m on LB 1.3.01 on Ubuntu 22.04.
2023-03-101.1K10The can is broken, and the pressure is rhythmic. This is the hydraulic part.On the other hand, the servo motor follows the rhythm of the energy storage tank and goes off and on.Oil and electricity are irrelevant.
2023-03-101.1K10In the process of equipment debugging, it was found that the servo motor could not reach the specified position. After troubleshooting, it was found that there was a problem with the IO line of the driver. It would be good if it was replaced. The servo motor uses position control, and the command pulse sent by PLC will be lost due to the poor conta...
2023-03-101.2K10Spiral gear is a common mechanical transmission device, which is widely used in various industrial equipment. Compared with other gears, helical gears have certain advantages, such as gradual contact, gradual departure, low noise, strong transmission capacity, etc. The following describes the advantages and applications of some helical gears. ...
2023-03-1091800The cutting drawing is not closed, and there is no problem with the drawing. How to solve this problem?
2023-01-091K20A series of problems will occur in the transmission process of gears. There are many kinds of gears. The general structure of gears includes gear tooth surface, normal surface, tooth top circle, tooth groove, end face, tooth root circle, base circle, scale circle, plastic deformation of tooth surface that may occur in gear transmission, gear fractu...
2023-03-0997011Getting cannot find C:\lbexport.aiCant find fix
2023-03-091.2K10
- Nessun Dato
Italiano
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski