Connection failure of CO2 laser cutting and engraving controller panel
If you encounter issues with the CO2 laser cutting and engraving control system, such as the mainboard being unusable or the panel connection not displaying, you can conduct an inspection as follows: ...
- RDC6585G
- RDC6442G
- RDC6685U
- RDC6445G
- RuiDa
Michael27200CO2 cutting and carving control system, how to install USB driver?
The following are measures on how to install USB drivers when using the CO2 cutting carving control system: 1. Connect the hardware: Connect the controller's mainboard to your computer using a USB c...
- USB
- RDC6442G
- RDC6445G
- CO₂ laser
- RuiDa
Adrian31411CO2 cutting and engraving system,laser engraving shows unevenness at the bottom,what should you do?
RDC6442G, RDC6445G, RDC6585G and other CO2 cutting and carving series control systems. If there is unevenness at the bottom of the carving, it can be adjusted according to the following methods. 1. C...
- RDC6585G
- RDC6442G
- RDC6445G
- laser engraving
- RuiDa
Gilbert30122CO2 cutting and carving control system, keeps moving after pressing the key once
When using the CO2 cutting and carving control system, if the button does not move or keeps moving after pressing the button once, the following points can be followed for troubleshooting and handling...
- RDC6585G
- RDC6442G
- RDC6445G
- CO₂ laser
- RuiDa
Clarence27500CO2 cutting and engraving control system: unable to download files to the board
When using the CO2 cutting and engraving control system, if you encounter a situation where files cannot be downloaded to the board, you can follow the steps below to troubleshoot and resolve the issu...
- RDC6442G
- RDC6445G
- control system
- CO₂ laser
- RuiDa
Payson31713What should you do if the positioning function of the CO₂ cutting and engraving series panel is not working?
When using the control system of the CO₂ cutting and engraving series, if the positioning function of the operation panel is not working, you can follow the steps below to troubleshoot and resolve the...
- RDC6585G
- RDC6442G
- RDC6445G
- CO₂ laser
- RuiDa
Gilbert30100- Non résolu
RDC6445G settings for CN1-Output not working right.
Hello again. Sorry for disturbign you again. I´m searching about 21 hours now in the internet and does not find any answer: My complete CN1 is not working right - I think. GND and +24V does work fine,...
- assist gas system
- RDWorksV8
- RDC6445G
- control system
- RuiDa
- 2 utilisateurs ont répondu
381 - Résolu
RDC6445G(EC) Firmwareupdate because DoorSensor-Issue
Hello. soem time ago I bougt a new Controller for my CO2-laser. I bought the RDC6445G(EC) version with also an new Display. I didn´t change the lasersystem for a long time, becaus I was long time in...
- RDWorksV8
- RDC6445G
- control system
- CO₂ laser
- RuiDa
- 1 utilisateur a répondu
419 Software Unable to Connect to CO2 Laser Cutting/Engraving Controller - Troubleshooting Guide
Basic Verification and Settings Check 1. Connection Method: In the software's (e.g., RDWorks) device connection settings, confirm that the selected connection method (Network/USB) exactly matches the...
- RDC6442G
- RDWorksV8
- RDC6445G
- CO₂ laser
- RuiDa
Payson36200CO2 cutting and carving control system: Insufficient cutting or carving depth
When using CO₂ laser cutting and engraving products equipped with a Ruida control system, insufficient cutting or engraving depth can be addressed by following the steps below for troubleshooting and ...
- RDC6442G
- RDC6445G
- laser engraving
- laser cutting
- RuiDa
Clarence33312How to encrypt the RuiDa CO ₂ cutting and carving control card motherboard?
In the settings of the operating software menu, enter the manufacturer's permission RD8888 for "Password Settings": A、 To change the 'Manufacturer Permissions', first enter the old password RD8888, an...
- RDC6442G
- RDC6445G
- CO₂ laser
- laser cutting
- RuiDa
Darren34121Lightburn and Ruida 6445G
when I start or send files from Lightburn to laser machine the head follows the tool path but no laser connected by Ethernet connection is good, reads machine seetings, saves steetings, modify ...
- RDWorksV8
- RDC6445G
- LightBurn
- control system
- RuiDa
jonnyfantatop1.3K30How to lock Ruida 6445G controller with password on startup?
Hello everyone, I am using a Ruida 6445G controller for my laser machine and I would like to know if it is possible to lock the machine (or the keyboard panel) with a password. My goal is: when the ...
- RDWorksV8
- RDC6445G
CBE1A5C71.5K31Dual outputs for Lasers
Hi. I have a RDC6445G unit in my 130w CO2 laser. Normally in Lightburn I can choose a Tube Tpe of Glass, RF1, or RF2. Now I want to add a Diode Laser to my unit so I can do very fine detail work that...
- RDC6445G
7E026F241.3K10banded horizontal lines
Good morning i have a co2 laser with 6445g controller i am engraving on granite. i have a problem with horizontally banded lines on engraving is there an upgrade of 6445g. if ibuy new like 6445gt will...
- RDC6445G
- laser engraving
- CO₂ laser
- RuiDa
029EE9D71.3K11
RDC6445G
38
Sujets24
Abonnés
En attente de réponses
- Where can I download the firmware upgrade file for the RDC6445 series controller?
- RDworksV8可以加工锤子画吗？
- After installing the RDWorksV8 plugin in CorelDRAW, how can I do engraving and cutting at the same time?
- Edge tracing for contour cutting
- How do I adjust the time displayed on the C320？
- problema na cnc
- Mantisoft User guide or Manual
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.