- No resuelto
Using LaserGRBL for laser engraving, there is an error in the axis direction
When I was using LaserGRBL for laser engraving, I found that the direction of the laser head movement was completely uncontrollable. Although clicking on the X-axis to move forward in the software, th...
- coordinate axis
- LaserGRBL
- laser head
- laser engraving
- 2 usuarios respondieron
57 - Resuelto
The laser did not reach the set power
I set a power (S-Max) in LaserGRBL, but engraving occurs at lower power. Why is this happening? How should I adjust?
- LaserGRBL
- laser engraving
- 2 usuarios respondieron
77 - No resuelto
How to set the rotation of Lasergrbl?
I initially used LaserGRBL, but I am not familiar with many operations. After opening the software, I searched for the rotation function on the interface, but the operation steps were not very intuiti...
- rotate
- LaserGRBL
- laser engraving
- 1 usuario respondió
198 There is an error in estimating the time using laser engraving software LaserGRBL
When using laser engraving software LaserGRBL, if the estimated time is inaccurate, please carefully read the following explanation: Each segment has its own programmed execution speed and its own le...
- LaserGRBL
- laser engraving
Gary10600LaserGRBL is missing some buttons/options
LaserGRBL detect GRBL configuration and remove (hide) some options if not compatible with your firmware/configuration. 1. M4 Dynamic Laser Power Mode is available only if your controller is updated w...
- LaserGRBL
- laser engraving
Adrian23300Processing with LaserGRBL, expected time may vary
Each segment has its own programmed execution speed and its own length (length of the segment, or lenght of the arc). The tracing movements G1, G2, G3, are performed at the speed F set in the GCode, ...
- LaserGRBL
Michael20500Processing using LaserGRBL, experience sharing of processing laser engraving machine moving too fast
If you find that the laser engraving machine moves too fast during laser engraving, causing inaccurate positioning or affecting engraving quality, you can solve this problem by adjusting the following...
- coordinate axis
- LaserGRBL
- laser engraving
Thomas23600Using LaserGRBL, The movement speed of the laser engraving machine is too slow
Set a speed in LaserGRBL, but engraving occurs at slower speeds. During processing LaserGRBL always command the speed you requested. However, there are reasons why the engraver may move slower. The f...
- motion system
- LaserGRBL
- laser engraving
Patrick33700LaserGRBL does not connect to my engraver
LaserGRBL work only with boards that implement Grbl. If you are sure that your board is Grbl compatible and you experience connection problem please verify that you are using the proper COM port and c...
- LaserGRBL
- laser engraving
Gilbert34610How to check if the focus is normal?
I have a Genmitsu 3030 CNC machine with a 5.5W laser installed on it. Overall, it works normally. My question is how to check if the focus is normal? LaserGRBL has a focus setting button. After pressi...
- LaserGRBL
Simon69030Is LaserGRBL compatible with CNC/milling machines?
Can LaserGRBL be compatible with CNC/milling machines? What should I pay attention to? Do I need to understand CAD?
- LaserGRBL
Smith75421My laser module stopped and burned for a few milliseconds
I have an Atomstack A5 Pro equipped with a 5W laser. The problem I encountered is that when carving or cutting, the laser stops for a few milliseconds and the carving leaves burnt spots at the stop. C...
- LaserGRBL
- laser engraving
- laser cutting
LWE1.2K40Not carving with power and speed
Hello friends, I have a problem with my Laser Atomstack S20Pro 20w - Blue laser. The laser does not engrave at power up to 0-20% and also does not engrave at speeds above 3000mm/m.-20000mm/m. For a be...
- LaserGRBL
- LightBurn
- laser engraving
Ethan1.3K41Unable to input commands in the console
I’m trying to see my GRBL settings, but I can’t type anything into the command window. Side note: I’m new to this, and I’m only trying to see these settings to address a different issue. I have a Monp...
- LaserGRBL
- fiber laser
Tim Johnson1.4K20Alarm 6, the stepper is stuck and unable to move. Is the stepper broken?
hello i havent used my 3018 in a while and am wondering what im doing wrong. i’m all set up wit grbl and lightburn 1.7.03 I power up and it begins to home motors just stuttuer terribly and wont move.h...
- motion system
- LaserGRBL
- LightBurn
Jack Wilborn1.3K10
LaserGRBL
16
Temas49
SeguidoresEsperando respuestas
- RDworksV8可以加工锤子画吗？
- Where can I download the firmware upgrade file for the RDC6445 series controller?
- After installing the RDWorksV8 plugin in CorelDRAW, how can I do engraving and cutting at the same time?
- Edge tracing for contour cutting
- How do I adjust the time displayed on the C320？
- problema na cnc
- Mantisoft User guide or Manual
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.