When I have a window open and connected to the laser and working. Why don’t I get one connection with to the laser from the second or third or fourth window . I have to close the first window to regai...

• laser source
• LightBurn

Silvano

2025-01-13

1.3K

2

0

I am using a co2 omtech laser with my fiber laser. When I switch between the 2 machines the orientation of my project has to be adjusted in machine settings each time. If I create a project on my co2 ...

• LightBurn
• fiber laser
• CO₂ laser

Cruise Wang

2025-01-02

1.3K

5

1

On one PC I open 2 Lightburn instances, the laser will connect to the first instance. In the second instance I am editing a project, but I am unable to send it to the laser because the laser is attach...

• LightBurn
• laser cutting

Erdogan

2024-12-31

1.3K

2

0

I was using Inkscape/K40 Whisperer and switched to Lightburn. When I import my previous designs that are set to vector & raster engrave, they only import as vector. Is there a way to change that? Do I...

• LightBurn
• laser engraving

Jack Wilborn

2024-12-24

1.4K

2

0

Hello. I jusy bought the new Creality rotary chuck to go with my Elegoo Phecda. I have the chuck plugged into the y axis cable. In lightburn, I have the rotary tool enabled, step set to what was provi...

• LightBurn

Clarence

2024-12-13

1.4K

2

0

Recently, when I try to engrave using my Xtool D1 pro, the engraving is way off. When I frame the job, everything looks fine. But once I start to engrave, the laser moves roughly 1.5 inches to the lef...

• LightBurn
• laser engraving
• laser cutting

Tim Johnson

2024-12-09

1.3K

2

0

The laser stops firing in the meddle of the job but the head doesn’t stops. When that happens, the head eventually stops, moves back and tries to keep engraving where it stops. The problem with that i...

• USB
• LightBurn
• laser engraving

Jack Wilborn

2024-12-09

1.3K

1

0

Hello, I also have the problem that when transferring data I get the error message that an error occurred while sending (the device may be busy or stopped). In the forum I found a post that you can tr...

• LightBurn

JOST

2024-12-06

1.2K

1

0

Hello. I recently upgraded Lightburn to 1.7.03. I am using Xtool Pro for my work. I am struggling to figure out why the laser head goes off in the wrong direction and then stops with a beep. It’s not ...

• galvo scanner
• LightBurn
• laser head
• laser engraving

Cruise Wang

2024-11-22

1.3K

3

0

I am sure I am not the only one here that has this happening, most likely with every K40 machine. My machine reaches max output milliamp output at 22-23% output in Lightburn. Would it be possible to c...

• power supply
• LightBurn

Hiroko

2024-11-20

1.5K

4

0

Ruida 6432g will it allow a rotary hooked up to the u axis  I have been trying to use the Y acess hooked to my 3 jaw rotary but it doesn't seem to let lightburn to change steps    can someone that rea...

• rotate
• coordinate axis
• RDWorksV8
• LightBurn
• RuiDa

A679218C

2024-11-14

1.2K

1

0

I purchased a new laser and computer and downloaded light burn onto the new computer…which is an updated version compared to what I have been using. I check all my settings to make sure they match my ...

• LightBurn
• laser engraving

Roderick

2024-11-12

1.4K

1

1

Hi. I am attempting to use a workflow that generates the following svg i need to import into lightburn. When I import it, the font reverts to Ariel. If I ungroup everything, I can change the font but ...

• LightBurn

Jack Wilborn

2024-11-09

1.4K

2

0

What I'm worried about is when I want to carve a circular logo on a water bottle, for example, if the image on Ligtburn is clean but distorted on my water bottle I checked the rotation and support se...

• rotate
• LightBurn
• laser engraving

Tim Johnson

2024-11-05

1.2K

2

0

Hi, Yesterday when i turned on the machine it started flashing red light and continually beeping. I tried restarting but nothing happened. then i moved the head in the middle and it stopped. After tha...

• LightBurn
• laser cutting

JOST

2024-11-04

1.4K

2

0