- Gelöst
How can the origin (0,0) be correctly set on a laser engraver to achieve accurate positioning?
I’ve only been using a laser for a few days and I’m already struggling with positioning and centering my designs. I usually like to set my origin (0,0) at the bottom-left corner of the material becaus...
- coordinate axis
- LightBurn
- laser engraving
- 5 Benutzer haben geantwortet
348 The laser does not work, it follows the path but does not carve or cut
I restarted the laser machine and this message appeared
- USB
- LightBurn
- laser engraving
- laser cutting
Roderick1.4K21- Gelöst
Using RDC8445S control system, cannot start from the positioning point set on the panel
I used the RDC8445S control system to carve workpieces today. I set a positioning point on the panel, but it did not start from that positioning point. What is the reason?
- RDC8445S
- laser engraving
- control system
- RuiDa
- 2 Benutzer haben geantwortet
288 How to set up engraving for upgrading a 10 watt laser to 40 watts
I am upgrading the 10 watt laser to 40 watts. Both are diode lasers. I carved on maple and hardwood with a 10 watt laser at a speed of 1500 millimeters per minute and a power of 30%, and the effect wa...
- laser engraving
Christian1.1K33- Gelöst
Can a diode laser cut or engrave acrylic? What colors, thicknesses, and techniques work best?
I’m looking for practical advice on cutting and engraving acrylic with a diode laser. My machine is a 12W Atomstack Swift. I’m already aware of the limitations of diode lasers when it comes to acryli...
- diode laser
- laser engraving
- laser cutting
- 2 Benutzer haben geantwortet
331 - Gelöst
Should I upgrade my CO2 laser to a combo system or buy separate CO2 and fiber lasers?
I’ve been running the same Chinese 100W 600×900 CO2 laser for close to 15 years now. A few years ago, I upgraded it with a Ruida controller so I could use LightBurn, and honestly, the machine has been...
- diode laser
- laser engraving
- fiber laser
- CO₂ laser
- laser cutting
- 2 Benutzer haben geantwortet
255 CO2 cutting and engraving system,laser engraving shows unevenness at the bottom,what should you do?
RDC6442G, RDC6445G, RDC6585G and other CO2 cutting and carving series control systems. If there is unevenness at the bottom of the carving, it can be adjusted according to the following methods. 1. C...
- RDC6585G
- RDC6442G
- RDC6445G
- laser engraving
- RuiDa
Gilbert30122- Gelöst
My RDC6332NM control system cannot engrave in RDWorksV8
My equipment uses the RDC6332NM control system, which allows for normal cutting. However, when I use the engraving function in RDWorksV8, it does not execute properly. What could be the reason for thi...
- password
- RDC6332NM
- laser engraving
- control system
- RuiDa
- 3 Benutzer haben geantwortet
280 - Gelöst
Which is more suitable for wood carving: a diode laser or a CO2 laser?
I’m planning to start a small laser engraving studio and, for now, I’ll only be engraving wood (patterns and text). I don’t plan to do cutting or work with other materials. Given these requirements, w...
- diode laser
- laser engraving
- CO₂ laser
- 6 Benutzer haben geantwortet
329 - Gelöst
What are the best diode laser brands? Please recommend some.
Hi all, I am currently looking for a small ~20 W laser diode for a prototyping project. The primary materials I plan to work with are approximately 3 mm thick plywood, with occasional use of acrylic ...
- diode laser
- laser engraving
- makers & DIY
- 5 Benutzer haben geantwortet
356 - Gelöst
Which laser cutting techniques have you found work best for achieving high-precision engravings?
Hi all, I’ve been trying out different approaches to improve the precision of my laser engravings, and I’d love to hear what’s worked well for others here. Lately, I’ve had good results by slowing do...
- laser engraving
- laser cutting
- 2 Benutzer haben geantwortet
332 - Gelöst
My laser engraver with the RDC6332NM only moves in one direction
My laser engravers use the RDC6332NM controller, but today I encountered a strange issue during operation: the machine only moves in one direction. Could someone please help me? Thank you.
- motion system
- RDC6332NM
- laser engraving
- control system
- RuiDa
- 2 Benutzer haben geantwortet
284 - Gelöst
RDC6585G cutting pattern not closed
My newly purchased cutting machine is equipped with the RDC6585G control system. Today, I conducted a test and found that the cutting pattern is not closed. I don't know if this is a problem with the ...
- RDC6585G
- laser engraving
- control system
- laser cutting
- RuiDa
- 2 Benutzer haben geantwortet
353 - Gelöst
The RDC6442G homes automatically.
My control system uses Ruida's RDC6442G. When I click "start" to process, it will automatically reset to the origin. Is it a problem with the reset button or other firmware? Any suggestions would be g...
- power supply
- RDC6442G
- laser engraving
- laser cutting
- RuiDa
- 2 Benutzer haben geantwortet
300 CO2 cutting and carving control system: Insufficient cutting or carving depth
When using CO₂ laser cutting and engraving products equipped with a Ruida control system, insufficient cutting or engraving depth can be addressed by following the steps below for troubleshooting and ...
- RDC6442G
- RDC6445G
- laser engraving
- laser cutting
- RuiDa
Clarence33312
laser engraving
128
Themen340
FollowerWarten auf Antworten
- RDworksV8可以加工锤子画吗？
- After installing the RDWorksV8 plugin in CorelDRAW, how can I do engraving and cutting at the same time?
- Where can I download the firmware upgrade file for the RDC6445 series controller?
- Edge tracing for contour cutting
- How do I adjust the time displayed on the C320？
- problema na cnc
- Mantisoft User guide or Manual
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.