1. Initialization parametersInitialize parameters before wiring. On the control card: select the control mode; Clear PID parameters to zero; When the control card is powered on, the enable signal is turned off by default; Save this state to ensure that the control card is in this state when it is powered on again.On the servo motor: set the...
2023-02-1623600What work needs to be done before starting the servo motor1) Measure the insulation resistance (not less than 0.5M for low-voltage motors).2) Measure the power supply voltage and check whether the motor wiring is correct and whether the power supply voltage meets the requirements.3) Check whether the starting equipment is in good condition.4)...
2023-02-1629500Daily maintenance of laser water chiller:1) Place the water chiller in a cool and ventilated place. It is recommended that the temperature be below 40 ℃. When using the laser chiller, the machine room should be kept clean and well ventilated, and the condenser should be cleaned regularly to ensure the normal operation of the unit.2) The wat...
2023-02-1638800Laser chillers are often used to cool UV lasers, CO2 laser glass tubes, semiconductor lasers, CO2 RF tube lasers, and fiber lasers of cutting machines, marking machines, engraving machines, and other equipment. Users can select suitable chillers according to different laser power. The installation and use of the laser chiller is very simple. The fi...
2023-02-16277001. Control temperature changeControlling the change of hydraulic temperature leakage in the process of various hydraulic power systems is an effective control measure to effectively control the leakage of hydraulic power transmission systems. From the control of the pipeline temperature of the oil tank and the pneumatic hydraulic press, control the...
2023-02-1630400The overflow leakage of parts in mechanical hydraulic power transmission system is mainly divided into two types: the internal part overflow leakage and the internal overflow leakage of main engine parts.The overflow leakage of internal components mainly occurs in the hydraulic cylinders such as the drive hydraulic valve, hydraulic pump, hy...
2023-02-1631200I power laser on and it only displays connecting to controller. I have disconnected the him from the controller and nothing homes. I have led 15 and 12 lit up with eithernet discounted. Homing switches work chiller input works and all drives are good no faults. Any ideas?
2023-02-0241620With the temperature getting hotter and hotter, the requirements of the processing plant for industrial refrigerators have been continuously improved. Our refrigerator equipment has created this new type of refrigerator with high performance, large output power and very good cooling effect in order to meet the strong suggestions of many customers....
2023-02-1532300The servo in the industrial control industry is generally the abbreviation of AC servo system. At the project site, the servo we refer to is the servo driver. However, servo driver and servo motor are an inseparable system, and they are connected by encoder cable and power cable. Generally, the servo driver bears the control command of the controll...
2023-02-1543500How does the PLC control the servo motor to automatically move left and right The servo motor drives the linear module to move from the left to the right and then automatically returns
2023-02-1531910Introduce three control modes of servo motorIf you have no requirements for the speed and position of the motor, just output a constant torque, which of course is torque mode.If you have certain accuracy requirements for position and speed, but you don't care much about real-time torque, it is better to use speed or position mode.If the up...
2023-02-1546000Hydraulic transmission system is widely used in construction machinery, and it is also an important executive mechanism of construction machinery. It plays an important role. The failure of hydraulic system will affect the operation efficiency of construction machinery and reduce the safety of construction machinery. In the actual operation of hydr...
2023-02-1530300Influence of gear type on noiseDifferent types of gears will have different meshing processes due to their different geometric characteristics. For example, under the condition of the same load and speed, through many application cases, it can be found that the noise of helical gear can be 3~10dB lower than that of spur gear;Influence of pr...
2023-02-1535600South London business invests in new printing and finishing equipment to free itself from the limitations of outsourced productionCMYUK, Shrewsbury: Standbuilder has invested in an Advance Sewing Automation V-TYPE/310C Digital, 2-Needle Lockstitch, Next-Generation Conveyor from CMYUK. This sewing machine will support the company’s new invest...
2023-02-1527100At the Photonics West Exhibition held in San Francisco from January 31 to February 2, ALIO Industries, the leading innovator of nano-precision motion control, will demonstrate its ability of accurate photon and fiber alignment applications at booth 4842.A glance at any industry vertical will show the increased use of LEDs and laser, optical...
2023-02-1525800
- Keine Daten
Deutsch
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski