While cutting on the Atomstack X24 Pro, the laser head encountered an obstacle on the work surface. Since then, the y-axis movement has not been performed correctly. The movement and noise are like rattling.Can anyone tell me what I should check to find the cause and, if possible, eliminate it?
vor einem Tag5600What setting in LaserGRBL controls turning on/off the Laser Focus Light?
vor einem Tag4800I am preparing to carve slate. Before that, what pigment should I use to color the slate？
vor 3 Tagen7420Can Lasergrbl be used for carving and cutting in the same project?My machine is a 10W laser
10-289130I just got a LE 4040 5.5W laser. How do I install the rotating attachment? I need a laser rotating roller with 360-degree rotation, three width settings, 195mm length, and 30–200mm diameter for use with an engraving machine.I can't find any settings to configure.
vor 2 Tagen7310Laser tube cutting machines hold a pivotal position in metal processing, enabling the fabrication of complex shapes, precise connections, and accurate cuts. They have revolutionized industries ranging from furniture manufacturing to aerospace. Scientific parameter optimization can significantly enhance cutting quality, increase production speed, an...
vor einem Tag5700Laser welding technology is increasingly applied in modern manufacturing. However, when welding aluminum alloys and copper alloys, these special materials present significant challenges that require specialized techniques to overcome.1. Core Welding ChallengesBoth aluminum and copper alloys present similar fundamental difficulties:Physical Prope...
vor einem Tag6800During the use of laser cutting machines, it is inevitable to encounter various problems, which can lead to unsatisfactory processing results. Here are 10 common problems that cause laser cutting failures.1. Contaminated Protective LensesTouching protective lenses with bare hands or neglecting to clean off dust can significantly reduce their tran...
vor 2 Tagen79001. Can diode laser cutting cut transparent acrylic?After fine adjustment of relevant parameters, the diode laser (≥ 30 W) can cut transparent acrylic with a thickness of about 6 millimeters.Laser PowerUse 65–70 % of the diode’s peak output to balance cut quality and speed.Cutting SpeedAim for 5–8 mm/s: slower speeds risk excessive melting; faster...
vor 3 Tagen6600I am looking for the best diode laser between $2000 and $3000. Reliability, usability, support, and functionality are all important.
10-2512720The weather is getting colder day by day, and machines and equipment, like humans, need to be kept warm. The following article introduces the key points related to antifreeze for laser cutting machines.1.Do not turn off the chillerAfter the laser cutting machine is not working, do not turn off the water cooler when ensuring that the power supply w...
10-289400Laser cutting of thick steel plates has become a part of daily manufacturing, but laser cutting of thick plates still faces some challenges: energy must penetrate deeply, molten material must be cleanly discharged, and the cutting edge must remain stable over long distances. The following are the main challenges faced by the workshop and mature sol...
10-2213621Myth 1: High equipment costsReality: Although the initial investment in a laser tube cutting machine may seem substantial, the long-term operational costs can be competitive compared to other cutting methods. Laser tube cutting machines offer high efficiency, minimal material waste, and reduced setup times, resulting in lower overall production cos...
10-2711400NEJE MAX 4 V2 E80， Equipped with Z-axis stepperI am trying to set lightburn so that when I input the material thickness, the z-axis will move to make it in focus.I have set the G54 z offset to -17, which is the focused position on the machine tool.When lightburn runs, it raises the z-axis to the height of the material, placing it in focus.My questi...
10-2411510In general, the most direct way to improve processing efficiency is to increase the laser power. When the 60000 watt laser cutting machine was launched, it sparked discussions.Industry experts believe that 60000 watts have the ability to fully replace plasma and flame cutting. Further increasing power does not contribute significantly to cutting e...
10-2513300
- Keine Daten
Deutsch
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski