Hello Does anyone knows, will LightBurn works with Ruida RDC8445S ? I try trial version, and Ruida always in disconnected state, Serial USB/Ethernet IP both not works. PS: RDWorks detect controller...

• RDC8445S
• controller
• LightBurn

96DED7E9

07-31

1.6K

5

0

Downloaded a SVG file fro Etsy. Transfered the file to Lightburn but the image just blinks on and off when selected. Why?

• LightBurn

Aaron

2023-03-07

1.6K

1

0

Hi everyone. Sorry if i placed this in the wrong section. Yesterday, I recieved my Aeon Fiber Laser ST50J. I was playing with some materials I had, and as I was testing and testing. I’d save the sett...

• LightBurn

Henry

2023-11-01

1.3K

1

0

My text is always mirrored when I engrave something. Can somebody tell me how to fix it?

• LightBurn

Cyril

2023-09-13

1.5K

1

0

Hi, new here but using Lightburn for about 2 years now. I use it to laser logo’s in bamboo. I now want to engrave text in aluminum but this is not possible with the laser I have so I want to buy a c...

• LightBurn

Darren

2023-07-22

1.5K

1

0

I am very new to Lightburn and laser engraving. When I hit the home button in Lightburn my Xtool D1 Pro goes up to the top left corner but hits the back wall and grinds for a few seconds. how do i cal...

• LightBurn

Nugent

2023-07-20

1.4K

1

0

I cannot get Continuous Jogging. It was there before and now not showing in Move Window. LB V 1.4. GRBL V 1f $J error:3Grbl ‘$’ system command was not recognized or supported. Yet I did see Continuous...

• LightBurn

Robert Evans

2023-09-27

1.3K

1

0

Completely new here and having a hard time understanding the material settings. In Laser Box, the settings seem to be way slower than the Lightburn settings (e.g., 360 versus 1800). Can someone enligh...

• LightBurn

Williams

2023-07-03

1.4K

1

0

With an image I created a circle with an offset by about 1 mm, and select fill. But when the laser cuts, it goes back-and-forth and back-and-forth. Takes forever. Is there a way that you can have the ...

• LightBurn

Vasili

2023-07-08

1.5K

1

0

I just installed my LightBurn camera, got it calibrated and it works fine. But, When I first open Lightburn and go to the Window menu, select camera control, it does not open. I’ve selected, unselecte...

• LightBurn

David

2024-01-04

1.2K

1

0

A question about LightBurn behavior. I made a “coin” that I am going to use as a sort of business card. I got the idea from The Louisiana Hobby Guy video. It cuts out the empty space in the coin and t...

• LightBurn

Abel

2023-03-09

1.4K

1

0

Hello All, Have recently purchased the xtool D1 and have been the past week trying to get it to engrave properly. When I click the origin to the top left corner, it flips my image upside down. When I ...

• LightBurn

Smith

2023-07-03

1.3K

1

0

I have my laser mounted secure, my camera is mounted secure, I run the calibration and the alignment, and everything is good for a while, then its out of align, I have to re calibrate it for it to wor...

• LightBurn

Clarence

2023-09-04

1.3K

1

0

Is it possible with Lightburn to move the laser to last position with a command and not the mouse curser?

• LightBurn

jessie

2023-10-27

1.2K

1

0

hello , can you plz tell me how do i add hadles to a node

• LightBurn

Cyril

2023-05-24

1.5K

1

0