Reasons for the problem of laser engraving not being round During laser engraving, there may be issues with roundness. This is mainly caused by the following reasons: 1. Unreasonable device parameter ...

• laser carving

Keegan

2024-12-23

1.3K

0

0

Please tell me how to fix this. I can’t even do the camera calibration. Thank you!

• laser carving

Roderick

2024-12-25

1.3K

3

0

have a Creality Falcon2 22 watt laser. I am running the most current version of a licensed version of Lightburn on a Dell XPS with Windows 11. Everything was working fine yesterday but when I went to ...

• laser carving

Roderick

2024-12-13

1.2K

3

0

Having a super hard time getting this image engraved on black slate. I have tried everything. Tracing Image, Removing background, Inverting, Negative etc.and no matter what I do I can not get the face...

• laser carving

Jack Wilborn

03-27

1.1K

2

0

On white bath panel mdf but as image this time. sculpfun s9 2000 mm at 75% using jarvis setting and air assist with good ventilation. Edited in gimp and inkscape to remove speckle and firm up lines.

• laser carving

Ethan

2024-11-07

1.1K

2

0

Hi Folks, i want to cut Parts for a Modell airplane, but there is only small differences between this parts, so i have to engrave some Numbers on them. I marked this Numbers and set them to Layer 02. ...

• laser carving
• laser cutting

Terrelle

2024-09-13

1.1K

1

0

Hello! I recently purchase a new machine, and it’s the first and only machine I have that has an auto-focus and a Z axis that uses a stepper motor. This got me thinking about how I can use this to eng...

• laser carving

Erdogan

2024-09-14

1K

1

0

Wood is one of the most common processing materials for laser engraving. Laser engraving wood has the advantages of fine carving effect, accurate positioning, and no mechanical wear. With the help of ...

• laser carving

Liam

02-28

961

0

0

Hello friends, I have a problem with my Laser Atomstack S20Pro 20w - Blue laser. The laser does not engrave at power up to 0-20% and also does not engrave at speeds above 3000mm/m.-20000mm/m. For a be...

• laser carving
• laser engraving

Ethan

03-26

955

4

0

The laser stops firing in the meddle of the job but the head doesn’t stops. When that happens, the head eventually stops, moves back and tries to keep engraving where it stops. The problem with that i...

• laser carving

Jack Wilborn

2024-12-09

957

1

0

Error 1: When carving fabric, the laser will burn through the material The first step in avoiding burning through fabrics when using laser engraving/cutting machines is to understand which fabrics can...

• laser carving

Ruddy

2024-07-22

951

1

0

I have an Atomstack A5 Pro equipped with a 5W laser. The problem I encountered is that when carving or cutting, the laser stops for a few milliseconds and the carving leaves burnt spots at the stop. C...

• laser carving
• laser cutting

LWE

03-31

885

4

0

Please see image. The text engraved in the right direction but was mirrored.

• laser carving

Narrator

03-20

876

2

0

We are setting up a laser machine to carve copper; From the first test, for example, by digging a small square at 0 degrees, a Z-dip angle of approximately 10-15 degrees can be obtained. What paramete...

• laser carving
• laser cutting

55455rml

2024-10-10

856

1

0

My LightBurn program is not fill engraving correctly. Is there a setting that needs to be adjusted to remove the lines left in the engravings? I ran two identical tests back to back. 1 in LightBurn a...

• laser carving

Jack Wilborn

2024-09-23

831

2

0