繁体中文

Feasibility Study on Composite Manufacturing of Laser Powder Bed Melting and Cold Casting

878
2024-06-06 14:46:49
查看翻譯

It is reported that researchers from the Technical University of Munich in Germany have reported a feasibility study on the composite manufacturing of EN AC-42000 alloy by combining laser powder bed melting and cold casting. The related research titled "Feasibility study on hybrid manufacturing combining laser based powder bed fusion and chill casting on the example of EN AC-42000 alloy" was published in Materials Science and Engineering Technology.

 



Laser based powder bed melting can be combined with casting to form a composite manufacturing process. This is to simultaneously utilize the advantages of both processes. In order to investigate the challenges associated with the use of aluminum alloys, researchers first conducted experiments using two common independent processes, the alloy EN AC-42000. Place the EN AC-42000 alloy samples that have undergone different surface treatments into a sand mold, and then cast them onto the aluminum melt. The contact area between the partially melted insert and the casting material was examined using an optical microscope. The results indicate that the main challenges include binding issues caused by the presence of oxides and high porosity. The high porosity can be traced back to the increase in porosity of inserts during laser powder bed melting.

 


Figure 1: Composite casting aims to combine the advantages of laser powder melting and die casting.

 


Figure 2: a) Experimental method scheme. The cylindrical aluminum sample is completely cast in. b) The image of inserting the sample into the four tubes inside the sand mold for the casting process.

 


Figure 3: Overview of samples after cutting, grinding, and polishing.

 


Figure 4: Microscopic image of the sample: Visible contact surfaces and pores are depicted in areas 1 and 2. The enlarged area 2 attempts to capture evidence of metal fusion or non fusion.

The purpose of this study is to gain a preliminary understanding of the challenges faced in combining laser powder bed melt additive manufacturing with casting. The results indicate that the porosity of EN AC-42000 alloy significantly increases. The increase in porosity is a major issue in the feasibility of the process, and further research should be conducted on possible solutions to prevent a significant increase in porosity.

In addition to porosity, there is also a certain degree of material fusion between castings and inserts manufactured by laser powder bed melting. In terms of process feasibility, these results mean that the oxide layer needs to be thoroughly removed and prevented from re growing after removal. In further research, methods for removing the oxide layer and stabilizing this deoxygenation state should be explored to make them suitable for components manufactured by laser powder bed melting.

Paper link: https://doi.org/10.1002/mawe.202300403

Source: Yangtze River Delta Laser Alliance

相關推薦
  • The research team developed additive manufacturing (AM) technology based on hydrogel injection, and related research was published on Nano Letters

    It is reported that the research team of California Institute of Technology has developed an additive manufacturing (AM) technology based on hydrogel injection, which uses two-photon lithography technology to produce 3D metal with a characteristic resolution of about 100 nm.The relevant research is published in the journal Nano Letters, titled 'Suppressed Size Effect in Nanopillars with Hierarchy ...

    2023-09-25
    查看翻譯
  • The wide application of laser plastic welding technology in the field of automobile manufacturing

    With the rapid development of society, people's demands for energy conservation, emission reduction, and safety in automobiles are increasing. Automobile manufacturers are seeking lightweight manufacturing processes for automobiles, changing traditional component packaging processes, and so on. Laser plastic welding technology has emerged, and below is a brief sharing of the application of plastic...

    2024-09-26
    查看翻譯
  • The birth of multi photon 3D laser printing technology: printing millions of particles within 1 second

    Multi photon 3D laser printing technology, as a disruptive micro manufacturing technology, is facing two major challenges: speed and material compatibility. However, the latest research has made breakthrough progress, successfully increasing printing speed tenfold while maintaining excellent detail accuracy.In this remarkable study, scientists abandoned the traditional single beam printing method ...

    2024-04-19
    查看翻譯
  • BMW uses WAAM 3D printing to optimize derivative designs

    BMW explained how to use WAAM (Arc Additive Manufacturing) starting from 2025 to manufacture lighter and stronger automotive components and reduce waste generation, in order to optimize the use of generative design tools.The demonstrated WAAM process uses aluminum wire raw materials directly deposited through laser welding heads, enabling automotive companies to manufacture lighter and more robust...

    2024-04-13
    查看翻譯
  • Shanghai Institute of Optics and Mechanics proposes a new solution for quartz glass as a visible light laser material

    Recently, Hu Lili, a research group of the Advanced Laser and Optoelectronic Functional Materials Department of the Shanghai Institute of Optics and Fine Mechanics, Chinese Academy of Sciences, proposed a new scheme based on rare earth ions Dy3+doped quartz glass as a yellow laser material, and the relevant research results were published in the Journal of the American Ceramic Society as "Effect o...

    2024-06-05
    查看翻譯