Hello, I'm upgrading an oscillating knife cutting machine. The machine had a Galileo controller. The PC used to operate it lost its hard drive. I couldn't configure the software from the backup I had.I purchased a Ruida RDD6616u controller from Wavetopsign on Aliexpress. I asked them for the installation manual and software on several occasions. I ...

Geozapata

2 天前

23

0

0

I have 150W Chinese Laser machine, it is is fitted with Ruida RDC6445S(EC), it is double head laser machine. Head 1 is connected with CN-5 and Head 2 is connected with CN-6.I have issue since I received the machine, Head 1 is firing laser normally, but Head 2 does not fire, I have double checked all the setting in Ruida controller and RDWorks.Whe...

C915A9E2

01-16

870

13

1

Import file failed, what is the reason?

Tim Johnson

05-20

338

5

0

When using the brush function to rotate the Z-axis instead of the U-axis for machining, there is always a gap reset action，

Ruddy

05-20

258

4

0

I am a novice, I tried to use an engraving machine to carve some patterns, but I found that the engraving machine did not carve in the correct direction of the pattern, but in the wrong direction. How can I change the setting? I use RDWorksV8 software

ElenaXavier

05-27

308

2

0

Buen día me pueden ayudar una máquina láser de 90cm x 60cm me sale en la máquina que el tamaño de trabajo es de 38cm x 30cm como puedo ponerla para 90x60

BFF58ACE

05-26

275

2

0

What version of RDworks is supposed to be used with this. I have v8.01.66 and am unable to connect via static wired ethernet or wifi. I can ping both ip's so I know it's online, just no software control via RDworks or lightburn

Colten

05-17

370

6

0

I use a new Monport 80w camera with RDC6442G.However, I hit autofocus in Lightburn or the Z-axis menu and the camera breaks. (This camera does not have a Z-axis limit switch).Can I disable the autofocus feature in the control panel or machine settings?I looked at the Ruida manual but it didn't help much with this problem.

ElenaXavier

05-15

335

1

1

The servo motor only moves in one direction,How should I handle it?

LWE

05-20

331

1

0

Fault analysis:1. The installation path is not selected correctly2. No VBA plugin downloaded3. The VBA plugin version is incorrect compared to the CAD version Solution:The reinstallation path is correct. After checking, it was found that the CAD version sent was 2023 and the VBA plugin version was 2018, which caused the failure. After re downlo...

Abel

05-19

247

0

0

Fault analysis:1. No fan enabled2. Relay wiring is incorrect3. Layer setting issue Solution:The layer parameters are set to not blow air

Aaron

05-19

222

0

0

Fault analysis:1. Layer output setting error2. The laser power setting is too small3. Wrong selection of the number of interchangeable heads Solution:Despite increasing the power, there is still no light, and the cutting action is normalUpon inspection, it was found that the number of interchangeable heads was set to 2, but in reality, there wa...

Kevin

05-19

229

0

0

Fault analysis:1. Enable multiple positioning points2. Failed to locate successfully3. Panel button malfunction4. Return setting error Solution:Upon checking the user parameters, it was found that the return method has been changed to return to the mechanical origin. Simply change the return to the positioning point

Marshall

05-19

208

0

0

Fault analysis:1. Abnormal reset parameters2. Panel reset button malfunction3. Unstable and undervoltage power supply voltage4. Program firmware malfunction Solution:Firstly, check whether the reset parameters are normal, whether the user parameter reset is turned on, whether the motherboard wiring is under voltage, and confirm that the output ...

Liam

05-19

223

0

0

HelloDoes anyone knows, will LightBurn works with Ruida RDC8445S ?I try trial version, and Ruida always in disconnected state, Serial USB/Ethernet IP both not works.PS: RDWorks detect controller by USB and IP (WiFi) - both success 

96DED7E9

05-15

260

1

0