1、 Servo systemA servo system refers to an automatic control system that utilizes the action of a component (such as a control rod) to reach or approach a predetermined state, and can compare the desired state (desired value) with the actual state, adjusting the control components according to their differences (sometimes the rate of change of this...

Darren

2024-02-18

999

1

0

The characteristics of servo drives1. The servo driver software program mainly includes the main program, interrupt service program, and data exchange program.2. The main program of the servo driver is mainly used to complete system initialization, LO interface control signals, and the setting of registers in various control modules within the DSP....

Marshall

2024-02-01

983

1

0

Stepper motors can achieve open-loop control of position and speed based on the number and frequency of pulses, making them an inexpensive, simple, and user-friendly control type of motor. They are increasingly widely used in the field of automation control. However, due to the fact that the stepper motor is not a closed-loop control, improper sele...

Silvano

2024-01-30

991

1

0

Is there a wiring method for servo motors that requires constant accuracy while following the rotor and rotating. If using a slip ring to connect the motor line and encoder line, will there be any out of step phenomenon? Is there any other better connection method.

roy

2024-01-26

879

1

0

Two sets of pulses are respectively connected to the same servo. One set of pulses controls the forward rotation of the motor, while the other set controls the reverse rotation of the motor. The two sets of pulses will not be triggered simultaneously. There is a program for servo pulse segments behind. The device is an old device that should have b...

Liam

2024-01-26

891

1

0

What is the sign for the servo to return to the origin? For example, there is a home button ->press the button ->the servo starts returning to the home point ->touch the home sensor (sensor closed) ->the servo starts decelerating ->the home sensor is disconnected (zero return completed)How to determine the completion of zeroing in t...

Aaron

2023-11-24

953

1

0

I remember to use a front and rear limit and a near origin for relative positions.Is it better to use absolute position or relative position for turntable servo? The turntable needs to be stuck once every time it passes through a workstation. What control method can be used to minimize the cumulative error as much as possible! And prevent the servo...

Kevin

2023-11-24

876

1

0

What is the reason why the laser motor autofocus is not ready？

Leon

2023-09-28

1K

1

0

Most precision stepper motor applications — especially those in automation and motion control — use a control method referred to as microstepping, which creates a sinusoidal (or nearly sinusoidal) current waveform, rather than the square wave of current produced with typical full-step control.The current rating of a stepper moto...

Tory

2023-08-24

1.1K

1

0

With each discrete step that a stepper motor makes, the inertia of the system causes the motor to slightly overshoot (or undershoot) the intended step angle. The motor then oscillates, or “rings,” until it finally settles at the commanded position. If the frequency of these step-by-step oscillations is at or near the motor’s natur...

Jen

2023-08-17

915

1

0

Delta Line has expanded its offering of motors with integrated electronics to include stepper motors. These smart stepper motors eliminate the need for a separate drive and controller, providing a complete stepper motor solution in a single, easy-to-integrate device.Delta Line’s ISI57 and ISI60 stepper motors with integrated electroni...

Payson

2023-08-16

839

1

0

With the SINAMICS S210 next generation servo-drive system, comprising a digitally native drive with wide range of corresponding motors and gearboxes, Siemens brings a new level of high-dynamic, motion control in mid-range operation to stand-alone and multi-axis machines, recently introduced to the North American manufacturing industry.This ...

Kevin

2023-08-15

1.3K

1

0

Kollmorgen has launched its AKMA servo motor built specifically for durability, cleanability, and versatility. The motor employs a hardened anodized aluminum surface to offer machine designers a cost-effective hygienic option to stainless steel in medium to heavy washdown applications.The lightweight design of the AKMA motor makes it easy t...

Aaron

2023-08-15

1K

1

0

1, motor encoder alarm(1) Fault causes① Wiring error;② Electromagnetic interference;③ encoder hardware damage caused by mechanical vibration;④ Pollution caused by the site environment;(2) Troubleshooting① Check the wiring and eliminate errors;② Check whether the shielding is in place, check whether the wiring is reasonable and solved, and increas...

Jen

2023-07-22

908

1

0

In order to meet the requirements of mechanical equipment for high precision and fast response, the servo motor should have a small moment of inertia and a large locked-rotor moment, and have as small a time constant and starting voltage as possible, and should also have a longer overload capacity. To meet the requirements of low speed and high tor...

John Trant

2023-07-22

883

1

0