This question has been bothering me. Can someone tell me what's going on? Thank you very much!

Andre J

2023-03-24

900

3

0

Laser control system in the off state how to do？

Silvano

2023-03-24

1K

1

0

For the life of me, I’m unable to get an accurate print/cut and wonder if someone can tell by my test cut where I should begin to fix?In the attached example. The top center circle is near perfect…the rest are slightly wonky when doing cut/print.The registration marks were lined up using a pulse for accuracy.Any help would be greatly a...

Miller

2023-03-22

998

1

0

Using TomWisdom, the Rotary menu is unavailable, although the rotary should be the same across hardware, just another use of the Y axis. Could this be enabled soon, please?

Cyril

2023-03-22

1K

1

0

I was doing a one pass at a time burn of a large logo on plywood. Forgot how many passes I used previously so I just burned and hit play again as it wasn’t going through. But on the third burn I hit “Home” in stead of play. When I pressed play after that the laser was off by 1 mm ruining the logo, and about a square foot of plywoo...

Terrelle

2023-03-22

1.2K

1

0

For example, Mitsubishi FX20GM module, compared with PLC pulse output control has what advantages?

Christian

2023-03-22

833

1

0

1. Make preparations for troubleshootingRead the hydraulic equipment instruction manual and hydraulic system diagram, master the hydraulic system structure, working principle, performance and equipment requirements for hydraulic system; Master the structure, working principle and performance of all hydraulic components in the hydraulic system; Rea...

Vasili

2023-03-22

977

0

0

Hard Hard Drive Crash(bummer) have since reloaded and got Lightburn up and running. Problem is somehow when I put it on the new drive the startup icon now has a MSoft UAC or user account control icon over the top and now requires me to give permission every single time I open LB. Can someone please tell me how to shut it off of this program??? Than...

Jen

2023-03-21

830

1

0

I am pretty good with Lightburn on my Ortur diode, but a noob to epilog. I am trying to get Lightburn designs into epilogs dashboard. Lightburn is a great design tools so I want to avoid subscription only software pirates.Do you tips for pushing designs from Lightburn into the epilog dashboard? I know I am just trying to export designs made in Lig...

John Trant

2023-03-21

779

1

0

I am having trouble lining up my material where the laser wants to travel. I seem to be off just a fraction to where the design is not centered. Please explain what I’m not doing correctly.Thank you

Jamie

2023-03-21

1.1K

1

0

If you use m0 to drive the ddrvi command to cause the servo action to travel 10000 pulses, and if the command is not fully executed (6000 pulses have been driven), m0 is disconnected. When m0 continues to be connected, do you want to travel 4000 pulses or 10000 pulses?

Marshall

2023-03-21

959

1

0

Do you want to use an emergency stop to power off, to disable all outputs, or to use an emergency stop to pause in the program?

Kevin

2023-03-21

884

1

0

1. First of all, it is necessary to clarify the type of cooling equipment. The range of use of industrial water chillers is very wide. Generally, they can provide users with 5 ℃ - 35 ℃ circulating cooling water to cool their equipment, thereby achieving cooling purposes and improving the production efficiency of enterprises. Industrial water chille...

Keegan

2023-03-21

924

0

0

I am making an Arrow of Light award 23" x 7.0" for Cub Scouts moving up. The Arrow and Light symbols are set to fill, 300 speed, 50 max power and 12.50 min power. The line interval is 0.1000 with 1 pass. The preview shows these two shapes filling 2 times each for a total time of 1:35:01. If I could get it to fill one time, I am sure the time would ...

Williams

2023-03-20

1.1K

1

0

Hello guys, I have problems with disconnections.I made a small, fine laser that I want to control via USB with an Arduino Uno clone and a CNC Shield V3.I have the problem that my laser keeps refusing to do its job.Regardless of whether I try it with LaserGRBL or with LightBurn, the machine always stops in the middle of the process.I’ve tried ...

Darren

2023-03-20

1.1K

1

0