I tried to make a 7.54mm round hole to accommodate a clock movement and I measured the shaft, it was 7.54mm so I made a circle and I input 7.65mm so it would be a good fit. When I burned it on a scrape piece of wood the diameter was like 1/2". can anyone tell me what Im doing wrong?

Jamie

2024-01-09

215

1

0

Ive got a galvo fiber laser with bjjcz controller and a k40 with the monport lightburn board. Which product license do i purchase?Do i get the 150$ Galvo licenseordo i get the 60$ gcode and 90$ galvo add on?Little confused here, thanks!!

Robert Evans

2024-01-08

223

1

0

How can I join A to B to make one line without using group. Either with or without the little tail at the top of A. I just can’t seem to work out how to do this in Lightburn so would appreciate some guidance - or is it just not possible?

John Trant

2024-01-08

290

1

0

I bought a Camera kit for my Elegoo Phedca (20W Diode) Followed the instructions by the seller. I am getting a skewed bottom\right side edge that is driving me nuts. I am following the Camera Lens calibration and getting great numbers .07-.12 but every time its done it comes out looking like the attached image

Jen

2024-01-08

254

1

0

There must be a simple way to have text entered vertically or converted vertically. Does anyone have any idea how to do this? I can’t seem to find it in the LightBurn documentation. I’m pretty sure there’s a shortcut but I don’t recall.

roy

2024-01-06

223

1

0

I upgraded from the stock Yorahome controller to a MKS DLC32 controller. When using the original controller I ran an engrave test that used the power scaling and it worked great. Now that I switched to the DLC32 and open the same file, the constant power mode it turned on.I am sure I messed up something in the settings and need help locating the de...

jessie

2024-01-06

217

1

0

I am having trouble with PNG files when I run a test I get this:

Patrick

2024-01-06

276

1

0

Hi all and thanks for your help.I created this logo for my, to be started up, engraving business. How do I get it from Lightburn to JPG or PNG? When I export it as SVG and open in Canva or Photoshop, is has the construction lines that serve as toolpaths for the text. I have tried to use “Content Aware Tracing Tool” but it makes a mess ...

Nugent

2024-01-05

250

1

0

I’m a newbie. Lightburn finds my Ortur Lasermaster 2 Pro S2 but won’t connect.The Laser panel indicates “Ready”. The Console displays “Waiting for connection …” twice, and then about a dozen "G0"s.The Move panel is dead - won’t move the laser head.However, Lasergrbl is able to operate the laser. I ca...

Vasili

2024-01-05

236

1

0

How do I reset Lightburn back to factory settings?

Payson

2024-01-05

223

1

1

The biopharmaceutical sand mill is a commonly used mechanical equipment, widely used in industries such as pharmaceuticals, chemicals, and food. The sand mill generates a large amount of heat during operation and requires refrigeration equipment for cooling in order to operate normally. Therefore, using a chiller as an auxiliary refrigeration equip...

Clarence

2024-01-04

215

1

0

Dear friend ! I managed to activate the license code in LightBurn. I was very happy about that. As a beginner, I have been familiar with LightBurn for a few days, but I managed to stop it so that it no longer executes any commands. Please help me to restore the software to its basic state, starting from scratch. reset.Unique assembly hobby laser en...

Gilbert

2024-01-04

299

1

0

I’m making jigsaw puzzles using a Atomstack A5 Pro. When using LaserGRBL I can cut my material at 100% 500 mm/min 4 passes. When using the same settings in Lightburn it is nowhere near cut. Is there some other setting I’m missing? The only difference I see is that LaserGRBL passes the entire drawing 4 times where Lightburn passes each l...

Cyril

2024-01-04

217

1

0

Hi, I'd like to add an extra 230Vac FAN to our lasercutter. The fan may only be active when the lazer itself is also active (cutting or scanning) When the proces is finished, the fan has to stop as well. In other words, the fan will only worg when there is a production of smoke. Any idea how I can control this?

DcoscfnG

2023-12-28

219

4

0

I just purchased the latitool laser. GRBL. I have a Mac book pro as well as a windows computer. Tried setting the laser up on both computersI follow all the instructions and have set the laser up with the x axis 400 y axis 400 and 0,0 is at the front left bottom corner.When the machine homes it goes up to the top left corner and grinders for atleas...

Williams

2024-01-03

219

1

0