1、 The optical path is not parallelDuring laser assembly, there may be situations where the optical path is not parallel, resulting in optical center deviation. In this case, it is necessary to readjust the optical path to make it parallel in order to solve the problem of optical center offset.2、 Lens wear and tearThe optical components in laser c...
2024-07-29272101. The motor cannot startPossible reasons:Power failure or power not connected.Parameter setting error.External control signal issue.terms of settlement:Check if the power supply is functioning properly and ensure that it is connected.Check the parameter settings of the frequency converter to ensure compatibility with the motor.Check if the exter...
2024-07-2924900Controlling the focus in laser cutting usually involves the following steps: 1. Adjusting the laser beam: Firstly, it is necessary to adjust the output power and wavelength of the laser to ensure that the quality and intensity of the laser beam are suitable for cutting materials.2. Focusing lens: Use a focusing lens to focus the laser beam into...
2024-07-26298101. It is necessary to clean the dirt on the machine tool and guide rail every working day to keep the bed clean. At the end of the day, turn off the air source and power, and at the same time, exhaust the residual air in the machine tool pipe.2. If leaving the machine for a long time, turn off the power to prevent non professionals from operating...
2024-07-2627900Common faults of synchronous motorsAlthough synchronous motors can maintain high work efficiency in most cases, there may still be some faults, as described below:1. Power reduction: Due to the inability of the rotor to rotate synchronously with the power supply, it may result in a decrease in the output power of the synchronous motor.2. Vibrati...
2024-07-2534510Laser marking machines, as an important tool for improving product identification quality and production efficiency, are increasingly widely used in the manufacturing industry. Faced with numerous laser marking machine brands and models in the market, choosing a device that suits the needs of one's own enterprise has become an important task. This ...
2024-07-2523100The automation and digital control of metal laser cutting machines are mainly achieved through the following key steps and technologies:1、 AutomationAutomatic loading and unloading system:The automated loading and unloading system can automatically feed the raw materials to be cut into the laser cutting machine and automatically take out the fini...
2024-07-2424210Handheld laser welding machine, as an emerging welding tool, works by converting electrical energy into laser and melting the welding wire and base material through high temperature to achieve welding. The following are common problems and their solutions for this device:1. Excessive wear of the protective lens of the welding gun head: The protec...
2024-07-2423600Rotor and controller mismatch: The rotor and controller of a brushless motor need to be matched to ensure normal operation. If not matched, it may cause overload and short circuit, thereby burning out the motor.Overload: If the brushless motor suddenly encounters excessive load during operation, it will also burn out. This may be due to changes i...
2024-07-23253101. Unstable laser outputUnstable laser output is one of the common faults in fiber lasers, which may lead to unstable processing quality or even processing failure.Possible reasons:(1) Laser lens contamination(2) Poor heat dissipation of laser(3) The laser power supply is unstableresolvent:(1) Timely clean the lenses inside the laser(2) Check if th...
2024-07-2326410This error happens everytime I power on the laser, I have confirmed by opening the laser that the laser autofocus is working, doing a manual A axis reset works perfectly but as soon as I enable Focus Ctrl in A axis vendor setting I get "A axis reset fail" each time the laser powers on. Can anyone help?Controller : Ruida RDC6563FG-LiteLaser Head : R...
2024-07-2127020With the widespread application of laser marking machines, their maintenance methods have also received widespread attention. In summer, not only is the temperature high, but the daytime is also relatively long, which means that every summer is the high-intensity working period of laser marking machines. Below are the maintenance methods for summer...
2024-07-2225920With the development of technology, industrial chillers are increasingly being applied in various fields of industry, making their due contributions to industrial production and improving product qualityAnd industrial chillers are also mechanical equipment, and after running for a long time, some problems may occur, among which corrosion is one of ...
2024-06-1422141Hi, I'm using the Ruida RDC6563 controller for a fiber laser cnc machine with the specifications of a BM110 laser head with auto focus servo. everything is running normally and have done a metal plate cutting test. but there is one issue, the autofocus function on the parameter layer does not work. but servo A axis runs normally on manual jo...
2023-02-1846071The maintenance of helical gear reducers is an important measure to ensure their long-term stable operation and extend their service life. The following are some basic points for maintenance and upkeep of helical gear reducers:Regular inspection: Regularly inspect the gearbox, including checking for any abnormal wear, cracks, or leaks on the appe...
2024-07-2222300
- 暂无数据
简体中文
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski