Türkçe

The United States is expected to use "AI+lasers" to deal with space debris in the future

449
2023-10-20 13:51:14
Çeviriyi gör

Due to the increasing threat of space debris in low Earth orbit around the Earth, space agencies around the world are becoming increasingly concerned about this. According to a new study funded by the National Aeronautics and Space Administration (NASA), it may be possible to send space debris that may be at risk of colliding with orbiting spacecraft to safer orbits through a laser network deployed in space in the future, the US "Space" website said on the 19th.

The report states that space debris has an increasing impact on the safety of spacecraft in various countries. When Amazon launched two internet prototype satellites on the 6th, it was forced to delay the launch for 6 minutes to avoid colliding with space debris.

In July of this year, due to the same reasons, the launch of India's historic "Lunar Ship 3" probe was also forced to be postponed. Although space debris has been a concern for decades, efforts to address this space debris have only recently truly begun to get back on track. The idea proposed by the Space Systems Warfare Research Laboratory at the University of West Virginia is to install artificial intelligence (AI) controlled space-based lasers on satellites or other specialized platforms for monitoring space debris. When a space debris is suspected of colliding with valuable space assets such as the International Space Station or satellites, laser pulses are used to push them into safer orbits.

According to the report, the statement released by the laboratory states: "Our goal is to develop a reconfigurable space-based laser network and AI algorithms. These algorithms will make this network possible and maximize its benefits." The plan has received funding from NASA and is still in its early stages. The ultimate goal is that the system will decide on which lasers to use to target a certain space debris, At the same time, ensure that the generated trajectory does not collide.

It is said that measuring the risk level of space debris is quite difficult because not every object in orbit can be tracked. According to data from the European Space Agency, the radar system on the Earth's surface is currently tracking approximately 34600 space debris, but there may still be 130 million fragments in orbit that cannot be accurately detected or tracked due to their small size. The report states that although the mass and volume of these space debris are small, their speed is fast enough to pose a threat to orbiting satellites or spacecraft.

Previously, countries had a preference for clearing space debris, but whether it was using high-strength materials to create "space debris nets" for salvage or using high-energy lasers for burning, there were limitations. In contrast, using space-based lasers to process small space debris may be more practical, as they can be sent into predetermined orbits using laser pulse irradiation, with relatively low power requirements for lasers. The report states that using multiple lasers can more effectively alter the trajectory of space debris, which "cannot be achieved by a single laser".

In March of this year, NASA released a report showing that space-based lasers are not affected by weather compared to ground based lasers. The report states that this AI powered space cleaning system not only has cost advantages, but its precise tracking ability for space debris also helps improve the safety of space launches.

Source: Global Times

İlgili öneriler
  • Assisting Gas Mixing to Promote the Development of Fiber Laser Technology

    Just ten years ago, fiber laser cutting machines were considered experts in thin plates. The stores quickly realized that they had to invest in them to compete, at least by reducing their instrument materials. For high-quality sheet metal cutting, CO2 laser is still the way to go. Of course, fiber lasers can cut thicker blanks, but the quality is not very good, and their speed advantage almost dis...

    2024-01-11
    Çeviriyi gör
  • Laser Photonics wins a large order from Lufthansa Technologies subsidiary

    Recently, American laser cleaning system developer Laser Photonics announced that the company has successfully secured an order for a cleaning technology laser cleaning system from Lufthansa Technik Puerto Rico, a technology subsidiary of Lufthansa, the largest aviation group in Europe.Lufthansa Technik is the world's largest independent provider dedicated to providing maintenance, repair, and com...

    2023-12-19
    Çeviriyi gör
  • Focusing on the headquarters of Kuaidiqin Gen, a place of innovation and prosperity

    Have you ever imagined finding exquisitely designed and vibrant buildings in an industrial park? The headquarters of Deutschengen in Germany is such a place that combines creativity and practicality.Carefully planned and focused sustainable architecture combines design and functionality, showcasing the best appearance of industrial architecture and a vivid practice of its corporate spirit and valu...

    2024-04-28
    Çeviriyi gör
  • MKS Instruments will build a factory in Malaysia

    Recently, American semiconductor equipment manufacturer MKS Instruments announced plans to build a factory in Penang, Malaysia to support the production of wafer manufacturing equipment in the region and globally. This development plan will be divided into three stages to build a new factory, and it is expected to break ground and start construction in early 2025.Why choose to build a factory in M...

    2024-06-26
    Çeviriyi gör
  • Shanghai Optics and Machinery Institute has made new progress in evaluating the anti laser damage performance of thin film optical components using different laser damage testing protocols

    Recently, the research team of the High Power Laser Element Technology and Engineering Department of the Shanghai Institute of Optics and Fine Mechanics, Chinese Academy of Sciences, has made new progress in evaluating the laser damage resistance and damage mechanism of 532nm thin film polarizers using different laser damage test protocols. The related achievements were published in Optical Materi...

    2024-04-25
    Çeviriyi gör